How to prevent seed tubes from plugging in PIEROBON Seeders?
To prevent seed tubes from plugging in your PIEROBON Seeders, ensure you are using clean seeds. Avoid pulling the machine backwards when the openers are in contact with the ground. Also, only lower the openers when the machine is moving forward.
How to improve opener penetration on PIEROBON Seeders?
To address poor opener penetration with your PIEROBON Seeders, adjust the gauge wheel for deeper operation or increase down pressure. Ensure harvest is carried out in good soil conditions and residue is spread evenly. Adjust the spring and opener depth, sharpen or replace openers, and choose the proper opener disks for your soil type.
Why is the planting depth uneven with PIEROBON Seeders?
Uneven planting depth in PIEROBON Seeders can be caused by residue laying in bunches, inadequate down pressure, or excessive speed on uneven ground. To resolve this, spread residue evenly across the field, increase down pressure to keep the gauge wheel in contact with the ground, and reduce speed when moving forward.
What to do if seed metering is uneven on PIEROBON Seeders?
If you experience uneven seed metering with your PIEROBON Seeders, it could be due to holes formed by dirty or too small seeds, or meters plugged by foreign substances. Use clean seeds and a seed ejector. Also, check and clean the meters.
How to prevent fertilizer tubes from plugging in PIEROBON Seeders?
To prevent fertilizer tubes from plugging in your PIEROBON Seeders, use dry, free-flowing fertilizer. Avoid pulling the machine backwards with the openers in contact with the ground. Ensure openers are lowered only when the machine is moving forward.
Why is the fertilizing rate incorrect on PIEROBON Seeders?
If the actual fertilizing rate is different than the estimated one on your PIEROBON Seeders, this could be due to an incorrect choice of gear speed or because the fertilizer has absorbed humidity. Check the surface to be fertilized and use dry fertilizer.
What to do if the drive wheel doesn't turn freely on PIEROBON Seeders?
If the drive wheel of your PIEROBON Seeders does not turn freely or turns unevenly, it may be because the hydraulic cylinders lowering cycle is not completed, the tires are not properly inflated, the wheel height adjustment is incorrect, cinematic toolbar components are locked, or the machine is not lowered completely. Lower the machine until the cylinders cycle is completed, inflate the tires to 20 pounds / inches 2, lower 1 or 2 grading adjustments, loosen locked components and lubricate, and lower the machine until cylinders stop-ends.
Why does my PIEROBON Seeders machine move to one side?
If your PIEROBON Seeders machine tends to move to one side, it could be due to a locked or misaligned wheel, or a disk marker excessively crossed. Align the wheel position using the lock and reduce the disk marker crossing.
Why is the furrow not closing with PIEROBON Seeders?
If the furrow is not closing properly with your PIEROBON Seeders, it is likely that the closing wheels are not adjusted properly. Reposition the closing wheels.
Why does only one marker descend on PIEROBON Seeders?
If only one marker descends on your PIEROBON Seeders, it could be because the hydraulic cylinders cycle was not completed or the sequence valve is dirty or damaged. Perform the complete cylinders cycle when the machine is raised, and clean or replace the valve.
Explains the hazard symbol for potential injuries due to improper equipment use.
Emphasizes reading and understanding all safety decals and manual procedures.
Warns to keep clear of moving parts and opener disks during operation and servicing.
Advises using safety locks on hydraulic cylinders to prevent injury.
States the implement is for one operator only; riders are at risk.
Highlights the need for lights and devices for safe road use.
Instructions for safe transport, including emptying tanks and locking components.
Guidelines for safe servicing and the use of proper protective equipment.
Warns about skin penetration by high-pressure fluids and leak checking procedures.
Precautions for handling chemicals safely, including personal protection.
Details the components of the row unit, including opener disk and gauge wheel.
Provides a table of technical specifications for TD 21 models.
Provides guidelines for tractor features and machine operation.
Details the process of moving the machine from transport to work position.
Describes how to adjust planting, fertilizing, and lucerne rates using gearboxes.
Details how to adjust the down-pressure of the openers.
Presents a chart for seed rates based on gear and sprocket combinations.
Provides a chart for fertilizer rates based on gear and sprocket combinations.
Explains adjustments for front no-till coulters, individual openers, and closing wheels.
Details technical specifications for TD Seeders models.
Guides the adjustment of opener disk hubs and bearings.
Tasks to perform after 8 and 100 hours of operation.
A chart detailing lubrication points and intervals.
Procedures for preparing the machine for storage after the season.
Lists causes and solutions for plugged seed tubes.
To Next Page
General