Pioneer DC-X20Z - User Manual

“This product is manufactured to comply with the radio inter-
ference requirements of EEC Directive 76/889/EEC and
|
82/499/EEC,””
H
Thank you for buying this Pioneer product.
Please read these operating instructions thoroughly, so you will know
how to operate your model properly. After you have finished reading
the instructions, put them away in a safe place for future reference.
For the sake of convenience, these operating instructions are based
on the model HE, and they can be used for the HB, YP, KU, KC, S
and $/G models.
The differences between the models are given below.
HE model:
For Europe excluding U.K. (’HE’ stamped on packing case}: Power
line voltage is AC 220 volts.
HB model:
For U.K. (‘HB’ stamped on packing case): Power line voltage is AC
240 volts.
YP model:
For Australia (‘YP’ stamped on packing case): Power line voltage is
AC 240 volts,
KU and KC models:
For U.S.A, and Canada (’KU’ or ‘KC’ stamped on packing case):
Power line voltage is AC 120 volts.
S and $/G models:
For destinations excluding above (’S’ or ‘S/G‘ stamped on packing
case): A 4-point (110 V/120 V/220 V/240 V) voltage selector switch is
provided,
NOTE:
Depending upon the model, the design of the power plug and the
power outlet differs.
The line voltage selector switch is located on the rear panel of the
unit. Please check that it is set properly before plugging the power
cord into an outlet. If it is not set properly, change the setting ac-
cording to the LINE VOLTAGE SELECTION( DandD/Gmodels only},
IMPORTANT NOTICE iFor KU and KC models)
The serial number for this equipment is located on the rear panel.
Please write this serial number on your enclosed warranty card and
keep in a secure place. This is for your security.
WARNING: TO PREVENT FIRE OR
SHOCK HAZARD, DO NOT EXPOSE
THIS APPLIANCE TO RAIN OR
MOISTURE.
STEREO DOUBLE CASSETTE
TAPE DECK AIViPLIFIER
DC-X20Z/DC-X21Z
FM/AM DIGITAL SYNTHESIZER TUNER
F-X20Z/F-X21Z
F-X207 L/ F-X?71 z {Only available in European
AM/FM STEREO TUNER
F-X102Z/F-X11Z
F-X10ZL/F-X11Z
{Only available in European.
countries.)
STEREO TURNTABLE
PL-X20Z/PL-X21Z
PL-X10Z/PL-X11Z
LINE VOLTAGE SELECTION
(S and S/G models only)
Before your model is shipped from the factory, the switch is set to the
power requirements of the destination; nevertheless, you should
check that it is set properly before plugging the power cord into the
AC outlet.
1. Disconnect the power cord.
2. Provide yourself with a medium size screwdriver.
3. Insert the screwdriver into the groove on the voltage selector and
adjust to the voltage value of your area.
te
a
Volts
120V__ 110V
Screwdriver
HE (for Europe excluding U.K.}, HB (for U.K.), YP (for Australia), |
KU (for U.S.A.) and KC (for Canada) models are not provided with
| a LINE VOLTAGE SELECTOR switch. |
QPIONEER’

Pioneer DC-X20Z Specifications

General

Power output	20W per channel (RMS)
Frequency response	20Hz - 20kHz
Total harmonic distortion	0.8%
Type	Stereo System
Input sensitivity	150mV
Output	Speaker terminals
Speaker load impedance	4 - 16 ohms
Signal-to-Noise Ratio	70dB
CD Mechanism	Single
Outputs	Headphones