Pioneer Elite VSX-37TX User Manual (English)

Questions and Answers:

T
Thomas AbbottAug 13, 2025
Why is there no sound coming from my Pioneer Stereo Receiver?
- B
  Brian FischerAug 13, 2025
  There could be several reasons for this. First, check if the connections are correct. Also, ensure that the sound isn't muted by pressing the MUTE button on the remote. The volume might be too low, so adjust the MASTER VOLUME. Check if the TAPE 2 MONITOR is ON and if so, press the TAPE 2 MONITOR button. Make sure the correct speakers are selected by pressing SPEAKERS (A/B). Finally, verify that the DIGITAL/ANALOG switch is set correctly.
T
Timothy BrownAug 16, 2025
How to reduce noise in Pioneer Elite VSX-37TX radio broadcasts?
- S
  Stephanie RodriguezAug 16, 2025
  To minimize noise in radio broadcasts, ensure you're tuned to the correct frequency. Check that the antenna is securely connected. Keep RF and digital cables away from the antenna terminals and wires. If using an FM antenna, fully extend it and position it for optimal reception, securing it to a wall. For weak signals, consider connecting an outdoor FM antenna. Adjust the direction and position of the AM antenna for best reception. If interference is caused by other equipment, turn off the equipment or move it away from the receiver; also, place the antenna further away from the equipment causing the noise.
K
Katherine JonesAug 20, 2025
What to do if no image is output on Pioneer Elite VSX-37TX?
- R
  Robert MitchellAug 20, 2025
  If there's no image output, first, ensure that all components are connected correctly. Then, verify that you've selected the correct input source by pressing the appropriate function button.
M
Mrs. Heidi Walker DVMAug 25, 2025
Why can't my Pioneer Elite VSX-37TX Stereo Receiver automatically select broadcast stations?
- S
  Sarah GrayAug 25, 2025
  The most likely cause is weak radio signals. To resolve this, try connecting an outdoor antenna.
P
Penny ReeseAug 28, 2025
Why is the subwoofer output so low on my Pioneer Elite VSX-37TX?
- C
  Carl PatrickAug 28, 2025
  The settings might be routing the signal away from the subwoofer. To increase the signal to the subwoofer, set it to PLUS or choose SMALL for the FRONT speakers.
J
Jill RobbinsSep 1, 2025
What to do if Pioneer Elite VSX-37TX Stereo Receiver buttons are not responding?
- L
  Linda Krause DVMSep 1, 2025
  If the unit isn't responding to button presses, it might be due to static electricity. Disconnect the power plug from the outlet, and then plug it in again.
J
joshuamcclainSep 4, 2025
Why doesn't the 5.1 channel indicator light up on my Pioneer Stereo Receiver when playing a Dolby Digital / DTS source?
- R
  Robert HayesSep 4, 2025
  The Dolby Digital / DTS source may not be 5 channels. There is no problem with the receiver, but if you want 5 channel sound you must play a 5 channel source.
E
Erin GonzalesSep 8, 2025
Why is there no sound when playing an LD with SIGNAL SELECT on 2 RF on my Pioneer Elite VSX-37TX?
- W
  Wendy JonesSep 8, 2025
  The LD may not be a Dolby Digital compatible disc. Set the SIGNAL SELECT to analog (make sure your LD player is hooked up with analog connections in addition to digital and 2 RF connections).

Pioneer Elite VSX-37TX Specifications

General

Type	AV Receiver
Channels	7.1
THD	0.09%
Frequency Response	5 Hz - 100 kHz
Input Sensitivity	200 mV (Line In)
Video Connections	Composite, S-Video
Surround Sound Formats	Dolby Digital, DTS
Speaker Impedance	8 ohms
Signal to Noise Ratio	92dB (MM), 96dB (line)
Dimensions	420 x 173 x 466mm