What to do if the magnet is rubbing against the sensor or transmitter on my Pioneer SGY-PM910H?
If the magnet is rubbing against the sensor or transmitter while riding, foreign objects may be attached to the magnet and rubbing against the transmitter or the junction box. Clean the transmitter, junction box, and magnet.
What to do if Pioneer Bicycle Accessories pedaling monitor sensor cannot pair to the Cyclocomputer?
If the Pioneer Bicycle Accessories pedaling monitor sensor cannot pair to the Cyclocomputer, activate the transmitter by rotating the bicycle’s crank set at least three times. The sensor automatically enters a sleep state if it remains still for five minutes.
Why is there noise when riding Pioneer SGY-PM910H and the transmitter and cover rattle?
If you hear noise and the transmitter and cover rattle when riding with Pioneer Bicycle Accessories, the screws for installing the sensor may have become loose, or the double-sided tape or parts of the sensors may have deteriorated. You may need to replace the double-sided tape or the parts of the sensors if they deteriorate. Check the screws for fixing the right transmitter, and then retighten them. Check if the parts of the sensors are installed correctly. If replacements are needed, please visit our website.
What to do if Pioneer Bicycle Accessories zero point calibration fails?
If zero point calibration fails on your Pioneer Bicycle Accessories, it could be due to water inside the sensors. Remove the batteries and allow the interior of the sensors to dry sufficiently. Then, perform zero point calibration again.
What to do if Pioneer SGY-PM910H Bicycle Accessories chain ring rattles?
If the chain ring rattles on your Pioneer Bicycle Accessories, contact your dealer. Check if the chain ring adapter is installed correctly. Press on the chainring in a clockwise direction to eliminate any play as you tighten the chainring bolts to the specified torque. Retorque the chain ring bolt periodically. Refer to the documentation for the crank set. Fix the position of the right transmitter after assembling the chainring.
Why is there a rattling noise when I am riding my Pioneer SGY-PM910H?
If you hear a rattling noise while riding, the screws used to install the sensor may be loose. Retighten the screws.
What to do if I cannot pair my Pioneer SGY-PM910H Bicycle Accessories with the Cyclocomputer in the power meter mode?
If you're unable to pair with the Cyclocomputer in power meter mode, it could be due to pairing failure between the right and left sensors. Check the sensor mode by pushing the push switch. If the left and right LEDs do not light orange, push and hold the push switch to switch to power meter mode.
What to do if zero point calibration fails on my Pioneer Bicycle Accessories?
If zero point calibration fails, it might be because the crank is subjected to external force or moving. Calibrate the sensor in still condition.
What to do if the red LEDs light for 10 seconds when batteries are inserted in Pioneer Bicycle Accessories?
If the red LEDs light for 10 seconds when batteries are inserted in your Pioneer Bicycle Accessories, contact your dealer.
What to do if Pioneer Bicycle Accessories crank set is obstructing the transmitter and cover?
If the crank set is obstructing the transmitter and cover of your Pioneer Bicycle Accessories, contact your dealer. Before selling the product, confirm that the crank set is supported. Shimano genuine chainrings are supported.
Details the strain gauge unit, magnet, and transmitters that make up the sensor system.
Explains how to change the system between pedaling monitor and power meter modes using the push switch.
Lists the User's Manual, Installation Manual, and Important Information for the User provided with the product.
Specifies which SHIMANO crank sets (FC-9000, FC-6800) are compatible with the pedaling monitor sensor.
Details all parts included in the product package, such as transmitters, cables, and covers.
Instructions on preparing the bicycle and environment for accurate sensor calibration.
Step-by-step guide to calibrate the zero point of the pedaling monitor sensors when the crank arm is perpendicular.
Verify the calibration by confirming the [Force Preview] values are within the specified range.
Specific instructions for calibrating sensors when the unit is set to power meter mode.
General| Brand | Pioneer |
|---|---|
| Model | SGY-PM910H |
| Category | Bicycle Accessories |
| Language | English |
To Next Page
