What to do if the drive on my PITBULL Compact Loader does not switch into neutral?
If the drive of your PITBULL Compact Loader doesn't switch into neutral, clean off any dirt on the three contacts and plugs on the underside of the drive motor and ensure that they snap into place. Also, replace fuse number 2 (15A) or fuse number 11 (10A) if they have blown.
What to do if hydraulic systems are not working properly on my PITBULL Compact Loader?
If your PITBULL Compact Loader's hydraulic systems aren't working correctly, start by checking and topping up the hydraulic oil. If the hydraulic oil is too hot or cold, allow the machine to cool down at idle without any load, ensuring the combination cooler is clear, or bring the machine up to operating temperature, respectively. Make sure the engine speed is sufficient by depressing the accelerator pedal. Ensure the correct power distribution is selected using the rotary wheel on the joystick. Avoid overloading hydraulic functions. Lubricate all lubrication points to reduce hinge point resistance. Change the hydraulic oil filter and return filter if they are dirty. Also, check the return line and lower the hydraulic oil level if the return doesn't flow to the tank quickly enough.
What to do if my PITBULL Compact Loader is not driving, but the engine is running?
If your PITBULL Compact Loader isn't driving but the engine is running, make sure the parking brake is released and that you're properly seated so the seat sensor detects you. Ensure the brake pedal isn't depressed and check all fuses. Verify the drive isn't in neutral; switch to the desired driving direction. Also, ensure the drive is unlocked and that there's enough hydraulic oil.
Why does my PITBULL Compact Loader have reduced power?
If your PITBULL Compact Loader has reduced power, replace the fuel filter if it's clogged, and clean or change the air filter if it's clogged. Drain and replace old fuel with fresh fuel. Avoid unnecessary hydraulic functions when using others. Warm up the machine before loading it if the engine temperature is too low. Check the engine oil filter and engine oil level to ensure proper lubrication.
How to troubleshoot a starter motor that is not running on a PITBULL Compact Loader?
If the starter motor of your PITBULL Compact Loader isn't running, first ensure the battery isolator is turned counter-clockwise. If that's not the issue, check and replace the main fuse (40A) if it has blown. Lastly, verify the battery voltage; recharge or replace the battery if the voltage is too low.
What to do if the internal combustion engine of my PITBULL Compact Loader does not start or stops immediately?
If your PITBULL Compact Loader's internal combustion engine won't start or stops immediately, first, check and fill the tank with diesel if it's empty. Replace fuse number 2 (15A) if it has blown. If there's a blockage during injection or the fuel filter is clogged, change the fuel filter. If the wrong fuel was used, drain and refuel with diesel. If the engine is too cold, preheat it.
Why does the lighting not come on in my PITBULL Compact Loader?
If the lighting on your PITBULL Compact Loader does not come on, replace the fuse(s) if they have blown. Replace the bulbs if they are burned out. Securely fasten the battery terminals if the cabling is disconnected.
What to do if the drive on my PITBULL Compact Loader does not switch into forward?
If the drive on your PITBULL Compact Loader does not switch into forward, clean off any dirt on the three contacts and plugs on the underside of the drive motor and ensure that they snap into place.
Why is hydraulic oil coming out of the vent on my PITBULL Compact Loader?
If hydraulic oil comes out of the vent of your PITBULL Compact Loader, make sure all cylinders are retracted and drain the hydraulic oil until the level has dropped to the indicated maximum, as there is too much hydraulic oil in the system.
What causes the driving motor of my PITBULL Compact Loader to get too hot?
If the driving motor of your PITBULL Compact Loader gets too hot, allow the machine to cool down in between uses if there's a prolonged heavy load. Lower the hydraulic oil level and check the return line if the return oil doesn't flow away fast enough to the tank. Reduce travel speed and relieve the strain on the working hydraulics as much as possible if the working hydraulics are heavily loaded while driving. If the hydraulic oil is too hot, allow the machine to cool at idle speed without load, and ensure the combination cooler is free of dirt or cover.
General| Brand | PITBULL |
|---|---|
| Model | X24-36 |
| Category | Compact Loader |
| Language | English |
To Next Page