Platinum Butlers Bell Kit User Manual

The pulley system inside the house
Step 1:
By now the cord should be attached to the top of the black rod and have been passed
through the hole that was drilled in the wall for the cord. The inside wall plate (B) will hide
the hole for the cord on the inside of the house. Attach a pulley (1xA) using one of the
big srews (1xF). The screw should be at the back of the plate and the pulley on the front. The
cord comes through the silver hole then runs around the pulley. The inside wall plate (B)
can be positioned, so that when the cord comes through the wall it can go in all directions.
The other pulleys in the hardware pack allow you to manouvre the cord around the walls to
the Butlers Bell.
Warning: We advise that you use as little length of cord as possible, and as few pulleys
as possible. If a lot of cord is used the tension on the inner spring is lost in the cord.
Mounting the Butlers Bell
Step 2:
Place the wall mounted stem (I) up against the wall. Depending on if your cord is
coming from the left or the right of the butlers bell.
CORD COMING FROM THE LEFT:
The brass arm needs to be past vertical with the top pointing in a north easterly direction (fig.1).
This is done by making sure that the inner spring is pointng down, facing south west (fig.2).
When the cord is attached to the brass arm it will pullback the arm to a vertical position causing
tension on the inner spring.
CORD COMING FROM THE RIGHT:
The brass arm needs to be past vertical with the top pointing in a north westerly direction.
This is done by making sure that the inner spring is piontng down, facing south east (fig.3).
When the cord is attached to the brass arm it will pullback the arm to a vertical position causing
tension on the inner spring.
Fig.1
Fig.2
Fig.3
Brass arm
Step 3:
When you have found the right postion, you can begin to mark out the holes in order to secure
the wall mounted stem (I). Once the holes are marked and drilled with the appropriate 6mm drill bit, insert
3 wall plugs (3 x E) and then fix the wall mounted stem to the wall using 3 screws (3xH).
Step 4:
Once the wall mounted spindle (I) is in place, replace the inner spring in your chosen direction (ref step 2).

Platinum Butlers Bell Kit Specifications

General

Brand	Platinum
Model	Butlers Bell Kit
Category	Accessories
Language	English

Summary

The Pulley System Inside the House

Step 1: Attaching the Cord

Attach pulley to plate, pass cord through wall plate and pulley, then around other pulleys.

Mounting the Butlers Bell

Step 2: Positioning the Brass Arm (Left)

Position brass arm past vertical, top northeast, inner spring southwest, for cord from left.

Step 2: Positioning the Brass Arm (Right)

Position brass arm past vertical, top northwest, inner spring southeast, for cord from right.

Step 3: Marking and Drilling Holes

Mark and drill holes for the wall mounted stem, insert wall plugs, and secure with screws.

Step 4: Replacing Inner Spring

Replace the inner spring in the chosen direction after the wall mounted spindle is in place.

Step 4: Attaching the Bell

Place the bell onto the wall mounted spindle, ensuring tension on the inner spring.

Step 5: Securing Components

Screw the rosette onto the wall mounted stem to secure all components in place.

Step 6: Routing the Cord to the Bell

Route the cord from the wall plate pulley to the bell, using an angle bracket if needed.

Step 7: Attaching Cord to Bell Arm

Pull bell arm, attach cord to it, ensuring it is taut for proper operation.

Introduction and Contents

Introduction

Welcome message and contact information for further assistance with the Butlers Bell Kit.

Bell Pull Installation

Step 1: Screw A & B Together

Assemble the black iron rod by screwing part A and part B together.

Step 2: Screw E onto B

Attach part E to part B of the black iron rod assembly.

Step 3: Slide Rod Through D

Slide the rod through component D, first through the plate, then over the next support.

Step 4: Slide Rod Through C & Attach G

Pass the rod through C, then the spring, and attach item G to the top of the rod.

Mounting Your Pull to the Wall

Step 2: Mounting Pull Plates

Position and drill holes for plates C & D, then secure them to the wall with screws.

Step 6: Re-insert Rod & Thread Cord

Re-insert rod, thread cord through G and barrel, then over wheel and through wall.