What to do if my Polaris Offroad Vehicle engine turns over but fails to start?
If your Polaris Offroad Vehicle engine turns over but fails to start, first, refuel if you are out of fuel. If the fuel is old, not recommended, or contains water, drain the fuel system and replace it with fresh, recommended fuel. Inspect the spark plug and replace it if it's fouled or defective. Also, recharge the battery to 12.8 VDC.
Why does my Polaris RZR 570 2017 engine stop or lose power?
If the engine of your Polaris Offroad Vehicle stops or loses power, start by checking if you're out of fuel and refuel if necessary. Inspect and replace any kinked or plugged fuel vent lines. Replace the fuel if water is present. Inspect, clean, and/or replace fouled or defective spark plugs, and ensure the spark plug gap is correctly set. Check and tighten any loose ignition connections and recharge the battery to 12.8 VDC if the voltage is low. Replace the fuel with fresh, recommended fuel if the current fuel is incorrect. Inspect and clean or replace a clogged air filter.
Why does my Polaris RZR 570 2017 engine run irregularly, stall, or misfire?
If your Polaris Offroad Vehicle engine runs irregularly, stalls, or misfires, start by inspecting, cleaning, and/or replacing the spark plug if it's fouled or defective. Ensure the spark plug gap is correctly set. Check and tighten any loose ignition connections. Replace the fuel if water is present with new fuel. Recharge the battery to 12.8 VDC if the voltage is low. Inspect and replace any kinked or plugged fuel tank vent lines. Replace the fuel with recommended fuel if the current fuel is incorrect. Inspect and clean or replace a clogged air filter.
What to do if my Polaris RZR 570 2017 Offroad Vehicle engine doesn't turn over?
If the engine of your Polaris Offroad Vehicle doesn't turn over, recharge the battery to 12.8 VDC if the battery voltage is low. Check and tighten all loose battery and solenoid connections. Inspect, clean, and reinstall the connectors of the loose electronic control box.
How to prevent drive belt wear on a Polaris Offroad Vehicle?
Drive belt wear or burn in a Polaris Offroad Vehicle can occur due to several reasons. To prevent this, use low range when loading onto a pickup or tall trailer, starting on steep inclines, towing/pushing, utility use/plowing, or when stuck in mud or snow. For climbing over large objects, shift to low range and carefully use fast, brief throttle. Warm the engine for at least 5 minutes in low ambient temperatures, and always warm up the belt by operating below 30 mph for one mile (5 miles or more when temperature is below freezing). Use the throttle quickly and effectively and install the recommended belt.
Why does my Polaris Offroad Vehicle engine backfire?
If your Polaris Offroad Vehicle engine backfires, inspect, clean, and/or replace the spark plug if it shows a weak spark. Set the spark plug gap to specifications or replace the plug if it's incorrect. Replace the fuel with fresh, recommended fuel if the current fuel is old or not recommended. Check all ignition connections and tighten any loose ones. Also, if water is present in fuel, replace with fresh recommended fuel.
Why does my Polaris RZR 570 2017 engine ping or knock?
If your Polaris Offroad Vehicle engine pings or knocks, replace the fuel with the recommended fuel if you are using poor quality or low octane fuel. Set the spark plug gap to specifications or replace the plug if it's incorrect.
General| Brand | Polaris |
|---|---|
| Model | RZR 570 2017 |
| Category | Offroad Vehicle |
| Language | English |
Explains signal words like DANGER, WARNING, CAUTION, NOTICE for hazard identification.
Encourages safety courses and familiarization with vehicle operation for rider safety.
Details required protective apparel for driver and passengers to reduce injury risk.
Outlines critical warnings for proper vehicle operation and safety precautions.
Identifies warning label placement and meaning on the vehicle for user awareness.
Identifies key external and internal components of the vehicle for user familiarity.
Explains steering wheel tilt adjustment for rider preference and comfort.
Details seat adjustment, removal procedures, and latch security.
Details 3-point seat belt usage, adjustment, and inspection for rider safety.
Covers operation of various vehicle switches like AWD, ignition, and lights.
Explains the gear selector positions (P, R, N, L, H) and proper shifting procedures.
Describes the instrument cluster, speedometer, indicator lamps, and rider information center.
Outlines procedures for breaking in the engine and drivetrain for longevity and performance.
Details essential checks before each vehicle use for safe operation and maintenance.
Lists fundamental practices for safe vehicle operation, including training and restrictions.
Provides guidelines for safely operating the vehicle with a passenger onboard.
Offers precautions for safe operation when traveling uphill, including terrain checks.
Explains precautions for operating the vehicle in water, including depth limits.
Provides guidance on safe cargo loading, weight limits, and towing practices.
Lists critical safety measures for operating the vehicle's winch to prevent injury.
Details the procedures for using the vehicle's winch safely and effectively.
Explains the dangers of shock loading the winch cable and how to avoid it.
Discusses engine, intake, and exhaust modifications and compliance with regulations.
Explains the engine's closed crankcase emission control system.
Details how exhaust emissions are controlled by engine design and EFI.
Provides a schedule for all required vehicle maintenance services based on hours, calendar, or miles.
Details specific lubrication points and recommended lubricants for the vehicle's components.
Covers engine oil recommendations, checks, and oil and filter change procedures.
Explains fluid checks and changes for the transmission and front gearcase.
Describes spark plug removal, replacement, and condition analysis for engine performance.
Covers brake system inspection, fluid checks, and maintenance procedures.
Details tire tread depth, torque specifications, and wheel removal/installation service.
Explains battery maintenance, removal, installation, and charging procedures.
Provides guidance on washing, polishing, storing, and transporting the vehicle properly.
Outlines the terms, duration, and coverage of the vehicle's limited warranty.
Explains the process and importance of vehicle warranty registration for coverage.
Details what is covered and excluded under the warranty terms and conditions.
Guides the user on procedures for obtaining warranty service from a dealer.
Provides specific warranty information related to emissions control systems.
To Next Page