Polyform A Series User Manual

Product Max. Circumference
A Series
A-0 25.1 in. 63.8 cm
A-1 34.5 in. 87.7 cm
A-2 45.5 in. 115.6 cm
A-3 53.4 in. 135.6 cm
A-4 64.4 in. 163.5 cm
A-5 84.8 in. 215.3 cm
A-6 106.8 in. 271.2 cm
A-7 122.5 in. 311.0 cm
F Series
F-1 18.8 in. 47.9 cm
F-02 23.6 in. 59.8 cm
F-2 25.7 in. 65.4 cm
F-3 25.7 in. 65.4 cm
F-4 26.7 in. 67.8 cm
F-5 34.5 in. 87.7 cm
F-6 34.5 in. 87.7 cm
F-7 47.1 in. 119.6 cm
F-8 47.1 in. 119.6 cm
F-10 56.5 in. 143.6 cm
F-11 66.6 in. 169.1 cm
F-13 91.1 in. 231.3 cm
Product Max. Circumference
G Series
G-3 17.3 in. 43.9 cm
G-4 20.4 in. 51.8 cm
G-5 27.6 in. 70.2 cm
G-6 34.5 in. 87.7 cm
HTM Series
HTM-1 19.8 in. 50.2 cm
HTM-2 26.7 in. 67.8 cm
HTM-3 33.0 in. 83.7 cm
HTM-4 42.4 in. 107.7 cm
LD Series
LD-1 27.0 in. 68.6 cm
LD-2 36.1 in. 91.7 cm
LD-3 42.4 in. 107.7 cm
LD-4 48.7 in. 123.6 cm
WS Series
WS-1 25.1 in. 63.8 cm
Note: Remove white plastic screw from the valve (located
near the ropehold). When inating with an air compressor,
set the psi to 2 lbs. pressure.
INFLATION CHART
INFLATION
Polyform products are designed to be inated to 2.1 lbs/0,15 bar of pressure. When inating with-
out a pressure gauge, ll the buoy or fender until the walls are fully expanded, but make certain
you can depress the wall at least 1/4 inch with light hand pressure. Measure the circumference and
compare it with the ination chart for proper pressure. Over ination will reduce the performance of
the product and may cause premature failure. Over ination voids the warranty.

Polyform A Series Specifications

General

Series	A Series
Shape	Round
Color Options	White, Black, Blue, Red
Features	UV resistant
Size Options	A0 to A7

Summary

Polyform Inflation Guide

Inflation Pressure and Over-inflation

Instructions on correct inflation pressure, how to check, and warnings about over-inflation to prevent damage.

Inflation Chart

Reference chart listing product specifications for proper inflation and note on air compressor use.

Inflation Steps

Step 1: Air Sources

Lists various air sources that can be used to inflate Polyform products.

Step 2: Valve Preparation

Instruction to remove the white plastic screw from the valve before inflation.

Step 3: Inflation Method

Guidance on using gas station/air compressor or hand/foot pumps with an inflation adapter.

Step 4: Checking Inflation

Method to check proper inflation by measuring circumference and thumb pressure.

Step 5: Sealing the Valve

Procedure to replace the screw after inflation, with a caution against over-tightening.