EN
WARNING
1. Recommended user's weight: 10 – 30 kg.
2. For outdoor use only.
3. For domestic use only.
4. Keep children in your direct line of sight, stay close, and actively supervise them when they are in or near this pool, and when you are filling and emptying this pool. When searching
for a missing child, check the pool first, even if the child is thought to be in the house.
5. Empty pool completely after each use, and store the empty pool in such a way that it does not collect water from rain or any other source.
6. Keep unsupervised children from accessing the pool by installing fencing or other approved barrier around all sides of pool. State or local laws or codes may require fencing or
other approved barriers. Check state or local laws and codes before setting up the pool.
7. Do not leave toys inside the pool when finished using it, since toys and similar items might attract a child to the pool. Position furniture (e.g., tables & chairs) away from pool, so that
children cannot climb on it to gain access to the pool.
8. Children can be drowned in very small amounts of water. Empty the pool when not in use.
9. Do not install the paddling pool over concrete, asphalt or any other hard surface.
10. Keep the instructions for further reference.
11. Pool and pool accessories are to be assembled and disassembled by adults only.
12. Never leave your child unattended - drowning hazard.
Setup Instructions
1. Location: Select a flat, level area of firm, compacted soil at least 2 m (78.7”) away from any structures or obstructions (e.g. fence, garage, stones, overhanging branches, laundry lines and
electrical wires, and free of any sharp objects.)
IMPORTANT: DO NOT install the product on mud, sand, soft or loose soil, deck, balcony, platform, wooden surfaces, concrete, asphalt or any hard surfaces. Certain grass types such as St.
Augustine and Bermuda may grow through the liner. Grass growing through the product is not a manufacturing defect.
2. Check the product for tears or punctures. Do not use a damaged product or one with defects.
3. Locate the water slide (if any) out of direct sunlight to reduce the likelihood of scalding.
4. To Inflate: Pump air in through the air valves one by one, starting from the base. When finished, close the valve caps and push the valves into the product to get a flat surface.
IMPORTANT: Always fully inflate all air chambers. The inflated product should be firm but not too hard. Do not over-inflate or use a high-pressure air compressor to avoid leak or damage.
If you cannot push the valve back into the product, deflate slightly.
5. To Deflate: Squeeze the base of valves to release all the air. Close the valve caps when finished.
AGES
2+
1
1. Inflate
If the Product is Equipped with 2-in-1 Valve:
2. Deflate 3. Seal
Remove Top Cap and press down
Inflation Valve. Then, pump air in.
Note: Before inflating, please press
Inflation Valve firmly into the exhaust port.
Remove Top Cap and Inflation
Valve. Then, let all the air out.
Close Top Cap tightly to seal the
valve after inflation/deflation.
To lock, press the valve
all the way down.
Top Cap
Inflation Valve
Exhaust Port
Inflation Valve
If the Product is Equipped with Hose Connector:
For products with water sprayers or hose connectivity, tighten the Threaded
Water Hose Connector to a standard garden hose.
For products with a Quick-Connect mechanism, tighten the mechanism between the
Threaded Water Hose Connector and a standard garden hose.
Threaded Water
Hose Connector
Quick-Connect
Garden Hose
Threaded Water
Hose Connector
Garden Hose
Maintenance & Storage
1. To Clean: Rinse with lukewarm mild soapy water and hang to dry. Never iron or brush. Do not clean with solvent cleaning agents - this will damage the product permanently.
2. Change the pool water frequently, particularly in hot weather, or when the water is noticeably contaminated.
3. Do not drag the product while it is loaded, sharp objects can puncture the product.
4. To Repair: Clean the repair area. Press the included repair patch firmly over the puncture/hole/leak, then wait for 30 minutes before re-inflating.
IMPORTANT: Do not modify this product and/or use any parts and accessories not supplied by the manufacturer. Replace defective parts according to the instructions of manufacturer.
5. To Drain: Remove all accessories, garden hose and toys (if any). Deflate the pool, then remove the drain valve stopper and drain. You can also push the sidewall down and inwards to empty
the pool completely.
6. To Store: Deflate, drain and completely air-dry the product. Gently fold, and store it in a dry place away from direct sunlight. The original packing carton can be used for storage.
Turn the water on slowly, and adjust to your desired spraying pressure by rotating the tap (if applicable).
2
Polygroup
Trading Limited Unit 606, 6th Floor, Fairmont House,
No.8 Cotton Tree Drive, Central, Hong Kong.
support.polygroupstore.com
To Next Page
Need help?
General
