To Next PageTo Next PageHow to clean clogged side-port of Porter-Cable PSH1 Paint Sprayer?
To clean a clogged side-port on your Porter-Cable Paint Sprayer due to dried material, soak the side-ports in thinner to dissolve the clog. Important: do not poke any opening with hard objects, as this may cause damage.
What to do if Porter-Cable Paint Sprayer leaks material from the nozzle when the trigger is released?
If your Porter-Cable Paint Sprayer is leaking material from the nozzle after you release the trigger, it could be due to several reasons: the fluid needle might be worn and needs replacement; there might be dried material in the tip of the nozzle, requiring a thorough cleaning; or the packing nut might be loose, in which case you should tighten the needle packing nut by turning it counterclockwise.
What to do if Porter-Cable PSH1 Paint Sprayer produces unatomized or spattered spray?
If the Porter-Cable Paint Sprayer is producing an unatomized or spattered spray, consider the following possible causes and solutions: * The material may be too heavy. If so, use a thinner material or use larger orifice fluid nozzle set. * There might be insufficient air pressure, so increase the pressure to within the limit. * The fluid pressure could be too high; in that case, reduce the pressure. * There might be dried material on the tip of the fluid nozzle or air jets of the air cap. Clean it.
Why is my Porter-Cable PSH1 Paint Sprayer spraying excessively foggy?
Excessive fog during spraying with the Porter-Cable Paint Sprayer may occur if the air pressure is too high for the viscosity of the fluid. To resolve this, try reducing the air pressure and/or opening the fluid control knob.
Why is my Porter-Cable PSH1 split spraying pattern?
A split spray pattern from your Porter-Cable Paint Sprayer can be caused by a couple of factors. It could be that the air pressure is too high; if so, turn the pattern control knob clockwise to decrease fan width. Alternatively, it may be due to insufficient fluid flow; in this case, turn the fluid needle adjusting nut counterclockwise to increase fluid flow.
What to do if Porter-Cable PSH1 Paint Sprayer has inadequate air delivery?
If your Porter-Cable Paint Sprayer has inadequate air delivery, it could be due to a few reasons. The air needle may be partially closed, so open the control knob. There might be dried material in the air jets or air cap, so clean it. Also, check for any obstruction in the air line and remove it.
What to do if material is leaking from the fluid inlet of the cup of Porter-Cable PSH1 Paint Sprayer?
If you notice material leaking from the fluid inlet of the cup on your Porter-Cable Paint Sprayer, the cause might be a loose cup or foreign substances present on or between the cup thread and fluid inlet. Try tightening the cup and cleaning the affected areas, or consider replacing the cup if necessary.
General| Brand | Porter-Cable |
|---|---|
| Model | PSH1 |
| Category | Paint Sprayer |
| Language | English |
Product title and type for the HVLP gravity feed paint spray gun.
Specifies the model number of the spray gun.
Emphasizes the importance of reading instructions before use.
Defines DANGER, WARNING, and CAUTION safety alert symbols.
General instructions to prevent serious injury and property damage.
Details flammability risks and prevention methods for spraying.
Warns about chemical reactions with specific solvents.
Highlights respiratory and skin hazards from paints and solvents.
Addresses risks from pressurized parts and airborne debris.
Warns about high-pressure fluid injection injuries.
Lists technical specifications like air inlet, pressure, and consumption.
Covers general safety, ventilation, and mask recommendations.
Key warnings and advice before starting spray gun operation.
Guidance on adjusting fluid control, pattern, and air quantity.
Steps for cleaning the spray gun after daily use.
Recommendations for lubricating moving parts.
Instructions for changing nozzle sets and available sizes.
Identifies common spray pattern issues, likely causes, and remedies.
Diagram and list of all parts with corresponding part numbers.
Details warranty periods for various Porter-Cable products.
Outlines steps for processing a warranty claim.
Lists items and conditions not covered by the warranty.
