Poulan Pro PPX19H46 User Manual (English)

Questions and Answers:

A
Amy WilliamsAug 20, 2025
How to fix a Poulan Pro PPX19H46 that will not start?
- S
  Samantha MartinezAug 20, 2025
  If your Poulan Pro Lawn Mower won't start, there are several potential causes. First, ensure that the fuel tank is filled. If the engine isn't choked properly, refer to the 'TO START ENGINE' section in the Operation section. If the engine is flooded, wait a few minutes before trying again. Other possible causes include a bad spark plug (replace it), a dirty air filter (clean or replace it), a dirty fuel filter (replace it), or water in the fuel (empty the fuel tank and carburetor, refill with fresh gasoline, and replace the fuel filter). Also, check for loose or damaged wiring. If none of these steps work, the engine valves may be out of adjustment, and you should contact an authorized service center/department.
J
Joshua ScottAug 22, 2025
Why is my Poulan Pro Lawn Mower hard to start?
- P
  Patrick MartinAug 22, 2025
  If your Poulan Pro Lawn Mower is hard to start, consider these possible causes. A dirty air filter can be the culprit, so clean or replace it. A bad spark plug can also cause this issue, so replace it if necessary. If you have a weak or dead battery, recharge or replace it. Also, a dirty fuel filter can make starting difficult, so replace it. Stale or dirty fuel could be the problem; empty the fuel tank and refill with fresh, clean gas. Check for loose or damaged wiring. If the problem persists, the engine valves may be out of adjustment, and you should contact an authorized service center/department.
K
Kimberly RamosAug 25, 2025
What causes Poulan Pro Lawn Mower engine clicks but will not start?
- B
  Beverly ZamoraAug 25, 2025
  If your Poulan Pro Lawn Mower engine clicks but won't start, the problem may be a weak or dead battery, so recharge or replace it. Corroded battery terminals can also cause this issue, so clean the battery terminals. Check for loose or damaged wiring. Another potential cause is a faulty solenoid or starter, so check or replace them.
X
xturnerAug 27, 2025
What to do if Poulan Pro Lawn Mower blades will not rotate?
- E
  emily71Aug 27, 2025
  If the mower blades on your Poulan Pro Lawn Mower will not rotate, check for an obstruction in the clutch mechanism and remove it. A worn or damaged mower drive belt can also cause this issue, so replace the mower drive belt. A frozen idler pulley or a frozen blade mandrel could be the problem; replace the idler pulley or the blade mandrel as necessary.
R
Richard KellyAug 30, 2025
Why Poulan Pro Lawn Mower engine will not turn over?
- F
  floweAug 30, 2025
  If the engine of your Poulan Pro Lawn Mower will not turn over, make sure the brake pedal is depressed. Also, ensure the attachment clutch is disengaged. A weak or dead battery can prevent the engine from turning over, so recharge or replace the battery. Check for a blown fuse and replace it if necessary. Corroded battery terminals can also be the cause; clean the battery terminals. Inspect for loose or damaged wiring. If these steps don't resolve the issue, the ignition switch may be faulty; check or replace it. Alternatively, the solenoid or starter may be faulty; check or replace them. If none of these solutions work, the operator presence switch(es) may be faulty, and you should contact an authorized service center/department.
T
Tina PerkinsSep 1, 2025
How to fix Poulan Pro Lawn Mower poor uneven cut?
- H
  Holly BrownSep 1, 2025
  If your Poulan Pro Lawn Mower is producing a poor, uneven cut, start by checking for a worn, bent, or loose blade; replace the blade and tighten the blade bolt if necessary. Ensure the mower deck is level and adjust if needed. Remove any buildup of grass, leaves, or trash under the mower. A bent blade mandrel can also cause an uneven cut, so replace the blade mandrel. Finally, check for clogged mower deck vent holes and clean around the mandrels to open the vent holes.
C
Christopher CrawfordSep 5, 2025
Why is my Poulan Pro PPX19H46 vibrating excessively?
- F
  fgibsonSep 5, 2025
  If your Poulan Pro Lawn Mower is experiencing excessive vibration, the cause may be a worn, bent, or loose blade. Replace the blade and tighten the blade bolt. A bent blade mandrel can also cause vibration, so replace the blade mandrel. Additionally, check for any loose or damaged parts and tighten or replace them as needed.
G
Gabriela GarrisonSep 7, 2025
Why are the headlights not working on my Poulan Pro Lawn Mower?
- A
  Andrew BryantSep 7, 2025
  If the headlight(s) on your Poulan Pro Lawn Mower are not working, first check if the switch is 'OFF' and turn it 'ON'. If the bulb(s) or lamp(s) are burned out, replace them. A faulty light switch can also cause this issue, so check or replace the light switch. Inspect the wiring and connections for any looseness or damage. Finally, check for a blown fuse and replace it if necessary.
A
Alexandra RamirezSep 9, 2025
What to do if Poulan Pro PPX19H46 battery will not charge?
- M
  Madison RamosSep 9, 2025
  If the battery of your Poulan Pro Lawn Mower will not charge, it could be due to bad battery cell(s), so replace the battery. Check and clean all cable connections to ensure they are secure. If your mower is equipped with a regulator, a faulty regulator could be the problem, so replace it. Alternatively, a faulty alternator could be the cause, so replace the alternator.

Poulan Pro PPX19H46 Specifications

General

Engine Power	19 HP
Cutting Width	46 inches
Transmission	Automatic
Deck Material	Steel
Fuel Capacity	3 gallons
Weight	500 lbs
Transmission Type	Hydrostatic
Engine Displacement	540cc
Cutting Height Positions	6
Drive System	Rear-wheel drive
Speed Settings	Variable
Fuel Tank Capacity	3 gallons
Oil Capacity	1.5 quarts
Warranty	2 years
Engine Type	Gasoline
Cutting Height	1.5-4 inches

Summary

SAFETY RULES

I. CHILDREN

Safety guidelines and age recommendations for children's operation.

II. GENERAL OPERATION

Instructions for safe operation, maintenance, and general use of the tractor.

III. SLOPE OPERATION

Guidelines and warnings for operating the tractor on slopes safely.

IV. TOWING

Instructions and precautions for towing attachments with the tractor.

V. SAFE HANDLING OF GASOLINE

Precautions for safely handling and storing gasoline.

GENERAL SERVICE

General maintenance and safety practices for overall tractor upkeep.

PRODUCT SPECIFICATIONS

CUSTOMER RESPONSIBILITIES

SUPPORT / HELP

ASSEMBLY

UNASSEMBLED PARTS

List and identification of parts included with the tractor for assembly.

TOOLS REQUIRED FOR ASSEMBLY

List of tools necessary for assembling the tractor.

TO REMOVE TRACTOR FROM CARTON

Step-by-step instructions for unpacking and removing the tractor from its shipping carton.

CONNECT BATTERY

Procedure for safely connecting the tractor's battery terminals.

ADJUST SEAT

How to adjust the tractor seat for optimal operator comfort and control.

TO ROLL TRACTOR OFF SKID

Instructions for safely removing the tractor from its shipping skid.

CHECK TIRE PRESSURE

Procedure for checking and adjusting tire pressure for optimal performance.

CHECK DECK LEVELNESS

Steps to ensure the mower deck is properly leveled for effective cutting.

CHECK FOR PROPER POSITION OF ALL BELTS

Verifying correct routing and installation of drive and mower belts.

CHECK BRAKE SYSTEM

Ensuring the tractor's brake system is functioning correctly before operation.

PRE-OPERATION CHECKLIST

A final checklist of items to verify before operating the tractor.

OPERATION

SYMBOL IDENTIFICATION

Explains the meaning of various symbols used on the tractor and in its literature.

SAFETY ALERT SYMBOLS AND DEFINITIONS

Explains the meaning of DANGER, WARNING, CAUTION, and other hazard symbols.

KNOW YOUR TRACTOR

Familiarizes the operator with the location and function of tractor controls and adjustments.

HOW TO USE YOUR TRACTOR

Basic instructions on operating the tractor, including braking, stopping, and throttle control.

MOVE FORWARD AND BACKWARD

Instructions on how to control the tractor's movement using the drive pedals.

ADJUST MOWER CUTTING HEIGHT

Guide on setting the appropriate cutting height for the mower deck.

OPERATE MOWER

Steps to engage and operate the mower blades safely.

REVERSE OPERATION SYSTEM (ROS)

Explanation and usage of the Reverse Operation System (ROS).

TO OPERATE ON HILLS

Safety precautions and procedures for operating the tractor on hills.

TO TRANSPORT

Instructions for preparing and transporting the tractor safely.

BEFORE STARTING THE ENGINE

Pre-start checks including engine oil level and adding gasoline.

PURGE TRANSMISSION

Procedure to remove air from the transmission for proper operation.

MOWING TIPS

Advice and techniques for effective and safe mowing.

MEASURING SLOPES FOR SAFE OPERATION

A visual guide to measure slope angles for safe tractor operation.

MAINTENANCE

MAINTENANCE SCHEDULE

A schedule outlining regular maintenance tasks and their frequency.

LUBRICATION CHART

Diagram and guide for lubricating various points on the tractor.

GENERAL RECOMMENDATIONS

Important advice on maintaining the tractor and understanding warranty coverage.

BEFORE EACH USE

Essential checks to perform before starting the tractor for each use.

BRAKE OPERATION

Procedures to check and adjust the tractor's brake system.

TIRE MAINTENANCE

Recommendations for maintaining tire pressure and condition.

OPERATOR PRESENCE & ROS SYSTEMS

Checks for the operator presence and Reverse Operation System (ROS).

BLADE MAINTENANCE

Guidance on maintaining mower blades for optimal cutting performance.

BATTERY MAINTENANCE

How to maintain the tractor's battery, including cleaning terminals.

V-BELTS

Information on checking and replacing V-belts for proper function.

TRANSAXLE MAINTENANCE

Procedures for cleaning and maintaining the transaxle cooling system.

ENGINE LUBRICATION

Guidance on selecting and using the correct engine oil and viscosity.

TO CHANGE ENGINE OIL

Step-by-step instructions for draining and refilling engine oil.

ENGINE OIL FILTER

Recommendation for replacing the engine oil filter.

AIR FILTER

Importance of air filter maintenance for engine performance.

ENGINE COOLING SYSTEM

How to ensure proper engine cooling by cleaning fins and shrouds.

SPARK PLUGS

Recommendations for replacing spark plugs for optimal engine starting.

MUFFLER

Inspecting the muffler and spark arrester for damage or fire hazards.

IN-LINE FUEL FILTER

Guidance on replacing the fuel filter for optimal fuel flow.

CLEANING

General cleaning procedures for the tractor and its components.

SERVICE AND ADJUSTMENTS

SERVICE AND ADJUSTMENT PRECAUTIONS

Essential safety warnings and steps to take before performing any service or adjustments.

TO REMOVE MOWER

Detailed steps for safely detaching the mower deck from the tractor.

TO INSTALL MOWER

Detailed steps for safely attaching the mower deck to the tractor.

TO LEVEL MOWER

Instructions for leveling the mower deck for optimal cutting performance.

TO REPLACE MOWER BLADE DRIVE BELT

Procedure for replacing the mower blade drive belt.

TO REPLACE MOTION DRIVE BELT

Procedure for replacing the tractor's main motion drive belt.

TO CHECK BRAKE

How to test and verify the proper function of the tractor's brake system.

TO REMOVE WHEEL

Instructions for removing a wheel from the tractor axle.

FRONT WHEEL TOE-IN/CAMBER

Information on factory settings for front wheel alignment (not adjustable).

TO START ENGINE WITH A WEAK BATTERY

Safety precautions and procedure for jump-starting the tractor's battery.

REPLACING BATTERY

Step-by-step guide for safely replacing the tractor's battery.

MINOR ELECTRICAL REPAIRS

Procedures for replacing bulbs, fuses, and checking wiring.

HOOD AND GRILL ASSEMBLY

Steps to remove and reinstall the tractor's hood and grill.

TRANSMISSION REMOVAL/REPLACEMENT

Information regarding transmission servicing and the need for purging.

THROTTLE CONTROL CABLE ADJUSTMENT

Note on throttle cable adjustment being factory preset.

STORAGE

TRACTOR STORAGE PREPARATION

Steps for preparing the tractor for long-term storage, including cleaning and lubrication.

BATTERY STORAGE

How to properly charge and store the tractor's battery for the off-season.

ENGINE STORAGE PREPARATION

Procedures for preparing the engine, fuel system, and cylinders for storage.

TROUBLESHOOTING

STARTING ISSUES

Identifies causes and corrections for various engine starting problems.

LOSS OF POWER

Identifies reasons for reduced engine power and how to correct them.

EXCESSIVE VIBRATION

Troubleshooting causes of excessive vibration during operation.

ENGINE CONTINUES TO RUN WHEN OPERATOR LEAVES SEAT

Troubleshoots a faulty operator presence control system.

POOR CUT QUALITY ISSUES

Addresses problems like uneven cut, non-rotating blades, and poor grass discharge.

ELECTRICAL SYSTEM PROBLEMS

Diagnoses issues with headlights not working or battery not charging.

DRIVE AND ENGINE OPERATION ISSUES

Covers loss of drive, engine backfiring, and engine stalling in reverse.

SERVICE NOTES

Related product manuals

Poulan Pro PPWT60022X

4 pages

Poulan Pro PPR20H42STA

48 pages

Poulan Pro PPX19H46 User Manual

Table of Contents

Questions and Answers:

Poulan Pro PPX19H46 Specifications

Summary

SAFETY RULES

I. CHILDREN

II. GENERAL OPERATION

III. SLOPE OPERATION

IV. TOWING

V. SAFE HANDLING OF GASOLINE

GENERAL SERVICE

PRODUCT SPECIFICATIONS

CUSTOMER RESPONSIBILITIES

SUPPORT / HELP

ASSEMBLY

UNASSEMBLED PARTS

TOOLS REQUIRED FOR ASSEMBLY

TO REMOVE TRACTOR FROM CARTON

CONNECT BATTERY

ADJUST SEAT

TO ROLL TRACTOR OFF SKID

CHECK TIRE PRESSURE

CHECK DECK LEVELNESS

CHECK FOR PROPER POSITION OF ALL BELTS

CHECK BRAKE SYSTEM

PRE-OPERATION CHECKLIST

OPERATION

SYMBOL IDENTIFICATION

SAFETY ALERT SYMBOLS AND DEFINITIONS

KNOW YOUR TRACTOR

HOW TO USE YOUR TRACTOR

MOVE FORWARD AND BACKWARD

ADJUST MOWER CUTTING HEIGHT

OPERATE MOWER

REVERSE OPERATION SYSTEM (ROS)

TO OPERATE ON HILLS

TO TRANSPORT

BEFORE STARTING THE ENGINE

PURGE TRANSMISSION

MOWING TIPS

MEASURING SLOPES FOR SAFE OPERATION

MAINTENANCE

MAINTENANCE SCHEDULE

LUBRICATION CHART

GENERAL RECOMMENDATIONS

BEFORE EACH USE

BRAKE OPERATION

TIRE MAINTENANCE

OPERATOR PRESENCE & ROS SYSTEMS

BLADE MAINTENANCE

BATTERY MAINTENANCE

V-BELTS

TRANSAXLE MAINTENANCE

ENGINE LUBRICATION

TO CHANGE ENGINE OIL

ENGINE OIL FILTER

AIR FILTER

ENGINE COOLING SYSTEM

SPARK PLUGS

MUFFLER

IN-LINE FUEL FILTER

CLEANING

SERVICE AND ADJUSTMENTS

SERVICE AND ADJUSTMENT PRECAUTIONS

TO REMOVE MOWER

TO INSTALL MOWER

TO LEVEL MOWER

TO REPLACE MOWER BLADE DRIVE BELT

TO REPLACE MOTION DRIVE BELT

TO CHECK BRAKE

TO REMOVE WHEEL

FRONT WHEEL TOE-IN/CAMBER

TO START ENGINE WITH A WEAK BATTERY

REPLACING BATTERY

MINOR ELECTRICAL REPAIRS

HOOD AND GRILL ASSEMBLY

TRANSMISSION REMOVAL/REPLACEMENT

THROTTLE CONTROL CABLE ADJUSTMENT

STORAGE