EasyManua.ls Logo

POWER ON BOARD VEC1095A User Manual

POWER ON BOARD VEC1095A
11 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Page #1 background imageLoading...
Page #1 background image
SMART AUTOMATIC
BATTERY CHARGER
OWNER’S MANUAL & WARRANTY INFORMATION
12 VOLT 2/10/25 AMP WITH 75 AMP ENGINE
ALTERNATOR VOLTAGE CHECK AND BATTERY RECONDITION
FUNCTIONS
• IMPORTANT SAFETY INSTRUCTIONS •
WARNING – RISK OF EXPLOSIVE GASES
WARNING - RISK OF EXPLOSIVE GASES
1. WORKING IN VICINITY OF A LEAD-ACID BATTERY IS DANGEROUS. BATTERIES GENERATE
EXPLOSIVE GASES DURING NORMAL BATTERY OPERATION. FOR THIS REASON, IT IS OF
UTMOST IMPORTANCE THAT EACH TIME BEFORE USING YOUR CHARGER, YOU READ THIS
MANUAL AND FOLLOW THE INSTRUCTIONS EXACTLY.
2. To reduce risk of battery explosion, follow these instructions and those published by the battery manufac-
turer and manufacturer of any equipment you intend to use in vicinity of battery. Review cautionary mark-
ings on these products and on engine.
GENERAL SAFETY
1. Use this charger for charging a LEAD-ACID battery only. It is not intended to supply power to a low voltage electrical sys-
tem other than in a starter-motor application. DO not use this battery charger for dry-cell batteries that are commonly used
with home appliances. These batteries may burst and cause injury to persons and damage to property.
2. Use of an attachment not recommended or sold by the battery charger manufacturer may result in a risk of fire, electric
shock, or injury to persons.
3. To reduce risk of damage to electric plug and cord, pull by plug rather than cord when disconnecting charger.
4. An extension cord should not be used unless absolutely necessary. Use of an improper extension cord could result in a
risk of fire and electric shock.
If extension cord must be used, make sure:
a. Pins on plug of extension cord are the same number, size, and shape as those of plug on charger.
b. Extension cord is properly wired and in good electrical condition; and
c. Wire size is AWG#14 (14 gauge) to 100 feet and AWG#12 for distances over 100 feet.
5. Do not operate charger with damaged cord or plug - take to a qualified service technician for replacement of the cord or
plug immediately.
6. Do not operate charger if it has received a sharp blow, been dropped, or otherwise damaged in anyway; take it to a qual-
ified service technician.
7. Do not disassemble charger; contact a qualified service technician when service or repair is required. Incorrect reassem-
bly may result in risk of electric shock or fire.
8. To reduce risk of electric shock, unplug charger from outlet before attempting any maintenance or cleaning. Turning off
charger controls will not reduce this risk.
9. Do not operate charger in rain or snow or use when wet.
10. Never charge a frozen battery.
SAVE THESE INSTRUCTIONS:
This manual contains important safety and operating instructions for battery charger Model VEC1095A
4140 SW 28TH WAY, FT. LAUDERDALE, FL 33312 • TEL: 954-584-4446 • FAX: 954-584-5556 • TOLL-
FREE 866-584-5504
VEC1095A
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Other manuals for POWER ON BOARD VEC1095A

Question and Answer IconNeed help?

Do you have a question about the POWER ON BOARD VEC1095A and is the answer not in the manual?

POWER ON BOARD VEC1095A Specifications

General IconGeneral
Input Voltage100-240 VAC
Output Voltage12V DC
Storage Temperature-40°C to +85°C
Frequency50-60 Hz
Efficiency≥85%
ProtectionOver Voltage, Over Current, Over Temperature, Short Circuit

Summary

Important Safety Instructions

Risk of Explosive Gases

Highlights dangers of explosive gases during battery operation.

General Safety Precautions

Provides essential safety guidelines for using the battery charger.

Personal Safety and Power Connection

Personal Precautions

Emphasizes personal safety measures when handling lead-acid batteries.

Power Cord Connection

Explains correct grounding and connection of the charger's power cord.

Charging Setup and Connections

Pre-Charge Preparation

Outlines battery prep, charger location, and DC connection safety.

Connecting Battery Outside Vehicle

Controls and Indicators

Indicators and Charge Rate

Advanced Features and Checks

Alternator Voltage Check

Details the steps for performing a no-load and under-load alternator voltage check.

Maintenance and Troubleshooting

Troubleshooting Faults

Guides users on diagnosing and resolving issues indicated by the fault LED.

Related product manuals