PowerA SPECTRA INFINITY - Customer Support and Warranty; Customer Service Contact; Two Year Limited Warranty Details

To Previous Page

ENGLISH

CONTENTS

• Spectra Inﬁnity Enhanced Wired Controller for Xbox

Series X|S

• Braided 10ft Snap-Lock Detachable USB cable

• User Manual

SET UP

Connect the 10ft USB cable by plugging it into any

available USB port on your Xbox console. Connect the

other end to the Micro USB port on your PowerA Enhanced

Spectra Inﬁnity Wired Controller. Hold down the Xbox

Button until your console powers “ON”. The controller’s

LED Connection Indicator will illuminate to indicate your

controller is connected.

NOTE: To remove cable, squeeze two side buttons near

port and pull gently. USB cable also includes inline release

plug closer to end of cable that will disconnect when

needed. For player and controller assignment reference

your ofﬁcial Xbox user’s manual.

LED PROGRAM FUNCTION

The controller has three separate light up Spectra Zones

that you can customize:

1. To enter LED Program Mode, hold the LED button

on the back of the controller for 2 seconds.

The light piping around the top housing of the

controller will blink, indicating that you’re now in

LED Program Mode.

2. The programmable Zone you’re in will ﬂash 3

times. To toggle through the 3 Zones, press

“Right” on the D-Pad. Note that Zone One is the

default starting zone.

3. Select one of the A/B/X/Y buttons to choose your

color: 5 shades of green 5 shades of red 5 shades

of blue 5 shades of yellow

4. Next, continue pressing the selected A/B/X/Y

button to toggle through 5 shades of that color.

5. Next, press “Left” on the D-Pad to program the

zone’s light effect, either “breathing” or solid.

6. You can also press “UP” and “DOWN” on the

D-Pad to select one of ten brightness levels.

7. To exit Program Mode, hold the LED button for

2 seconds. All 3 LED Zones will ﬂash 3 times to

indicate you are now out of LED Program Mode.

8. To quickly turn off the LEDs completely, just

press the LED Program Button once. Press again

to turn the Spectra lighting feature back on.

TRIGGER LOCKS

• Adjust pull-distance of the triggers by sliding lock

switch on back to the left or right

• Each trigger can be adjusted separately

ASSIGNING ADVANCED GAMING BUTTONS

1. Press and hold the Program Button for 2-3 seconds on

the back of the controller. The program LED indicator will

ﬂash, signaling the controller is in assign mode.

2. Press 1 of the following buttons (A/B/X/Y/RB/LB/RT/LT/

Left Stick Press/Right Stick Press/D-pad) to re-assign.

Then press the Advanced Gaming Button (AGR or AGL)

that you wish to assign. The Program LED indicator will

stop ﬂashing, signaling the Advanced Gaming Button

has been set.

3. Repeat for the remaining Advanced Gaming Button.

NOTE: Advanced Gaming Button assignments will remain

in memory even after disconnected.

RESETTING ADVANCED GAMING BUTTONS

1. Hold the program button down for 2-3 seconds. The

LED Connection Indicator will slowly ﬂash, signaling the

controller is in program mode.

2. Press and hold the assigned AGR/AGL Button for 5

seconds to reset to no function.

USING THE SHARE BUTTON

Refer to Xbox documentation for details on functions and

features related to the Share button.

USING THE HEADSET DIAL

Once you plug the 3.5mm jack from your headset into the

controller, Dial will become active and LED will turn red

to indicate chat is muted. Press down on dial to mute/

unmute chat. To adjust volume, tap left or right to adjust

step by step, or press and hold left or right to adjust

volume to full up or full down.

NOTE: Audio controls within Xbox Settings will take ﬁrst

priority, followed by the the Headset dial, and ﬁnally any

audio or mute controls on your headset. Refer to your Xbox

and headset documentation for additional details.

TROUBLESHOOTING

For current FAQs, visit PowerA.com/support

Q: Controller will not connect to Xbox console?

A: Conﬁrm your Xbox console is powered “ON”.

A: Conﬁrm your TV is set to the proper Video Input and that

you can see the Xbox console interface on your TV screen.

A: Conﬁrm cable is properly connected to you Xbox console.

A: Conﬁrm cable is properly connected to your PowerA

Enhanced Wired Controller.

Q: Controller is connected but has no function?

A: Conﬁrm you are using the Player #1 controller. For more

troubleshooting refer to your Xbox console User Manual.

WARNING: READ BEFORE PLAYING

A very small percentage of individuals may experience

epileptic seizures when exposed to certain light patterns

or ﬂashing lights. Exposure to certain patterns or while

playing video games, may induce an epileptic seizure

in these individuals. Certain conditions may induce

previously undetected epileptic symptoms even in persons

who have no history for prior seizures of epilepsy.

If you, or anyone in your family, have an epileptic condition,

consult your physician prior to playing. If you experience

any of the following symptoms while playing a video game

– dizziness, altered vision, eye or muscle twitches, loss of

awareness, disorientation, any involuntary movement, or

convulsions – IMMEDIATELY discontinue use and consult

with your physician before resuming play.

MOTION WARNING

Playing video games can make your muscles, joints, skin

or eyes hurt. Follow these instructions to avoid problems

such as tendinitis, carpal tunnel syndrome, skin irritation

or eyestrain:

• Avoid excessive play. Take a 10 to 15 minute break every

hour, even if you don’t think you need it. Parents should

monitor their children for appropriate play.

• If your hands, wrists, arms or eyes become tired or sore

while playing, or if you feel symptoms such as tingling,

numbness, burning or stiffness, stop and rest for

several hours before playing again.

• If you continue to have any of the above symptoms or

other discomfort during or after play, stop playing and

see a doctor.

FCC STATEMENT

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions:

1. this device may not cause harmful interference, and

2. this device must accept any interference received,

including interference that may cause undesired

operation

WARNING: Changes or modiﬁcations to this unit not

expressly approved by the party responsible for compliance

could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found

to comply with the limits for Class B digital device,

pursuant to Part 15 of the FCC Rules.

CAN ICES-003(B)/NMB-003(B)

This device contains licence-exempt transmitter(s)/

receiver(s) that comply with Innovation, Science and

Economic Development Canada’s licence-exempt RSS(s).

Operation is subject to the following two conditions:

1. This device may not cause interference;

2. This device must accept any interference, including

interference that may cause undesired operation of

the device.

MANUFACTURED BY

ACCO Brands USA LLC

4 Corporate Way, Lake Zurich, IL 60047

ACCOBRANDS.com | POWERA.com

MADE IN CHINA

CONTACT/SUPPORT

For support with your authentic PowerA accessories,

please visit PowerA.com/Support.

WARRANTY

2-Year Limited Warranty: Visit PowerA.com for details.

AUSTRALIAN WARRANTY STATEMENT

This product comes with guarantees that cannot be

excluded under the Australian Consumer Law. You

are entitled to a replacement or refund for a major

failure and for compensation for any other reasonably

foreseeable loss or damage. You are also entitled

to have the goods repaired or replaced if the goods

fail to be of acceptable quality and the failure does

not amount to a major failure. If purchased within

Australia or New Zealand, this product comes with a

One-year warranty from date of purchase. Defects in

the product must have appeared within One year from

date of purchase, in order to claim the warranty. All

warranty claims must be facilitated back through the

retailer of purchase in accordance with the retailer’s

return policies and procedures. Any expenses incurred,

as a result of returning the product to the retailer of

purchase are the full responsibility of the consumer.

ENHANCED

WIRED

CONTROLLER

USER MANUAL | Manuel de l’utilisateur | Bedienungsanleitung

Manual de usuario | Manuale per l’uso | Manual do usuário

Directional

Pad

3-Way Trigger lock 3-Way Trigger lock

LED Program

Button

LED Connection

Indicator

Button

Xbox

Button

View

Button

Headset

Dial

Braided 10-ft Snap-Lock

Detachable USB Cable

Program

Button

Advanced

Gaming Buttons

Anti-friction

Rings

3.5mm Stereo

Headset Jack

TAP OR HOLD TO ADJUST WIRED HEADSET

VOLUME (LEFT-DOWN, RIGHT-UP)

PRESS TO MUTE (RED) OR UNMUTE

CHAT IN WIRED HEADSET.

A, B, X, & Y

Buttons

ZONE 1

ZONE 2 ZONE 3

Customer Service

Service client

Kundendienst

Servicio a clientes

Assistenza clienti

Apoio ao Cliente

PowerA.com/Support

TWO YEAR LIMITED WARRANTY

For warranty details or support with your authentic PowerA accessories, please visit PowerA.com/Support.

Beschränkte 2-Jahre-Garantie Informationen zur Garantie oder Unterstützung zu Ihrem PowerA-Originalzubehör ﬁnden Sie unter PowerA.com/Support.

Garantía limitada de dos años Si quieres más información sobre la garantía o necesitas ayuda con tus accesorios originales de PowerA, visita

PowerA.com/Support.

Garantie limitée de deux ans Pour plus de détails sur la garantie ou pour obtenir une assistance pour vos accessoires PowerA d’origine, veuillez

consulter le site PowerA.com/Support.

Garanzia limitata di due anni Per i dettagli sulla garanzia o per richiedere assistenza per i tuoi accessori PowerA autentici, visita la pagina

PowerA.com/Support.

Garantia limitada de dois anos Para mais informações sobre a garantia ou os acessórios originais da PowerA, visita PowerA.com/Support.

PowerA SPECTRA INFINITY - Customer Support and Warranty; Customer Service Contact; Two Year Limited Warranty Details

Related product manuals