This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
this device may not cause harmful interference, and
this device must accept any interference received, including interference that may cause undesired operation
WARNING: Changes or modifications to this unit not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for Class B digital devices, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/ TV technician for help.
CAN ICES-3(B)/NMB-3(B)
This device contains license-exempt transmitter(s)/ receiver(s) that comply with Innovation, Science and
Economic Development Canada’s license-exempt RSS(s). Operation is subject to the following two conditions:
1. This device may not cause interference;
2. This device must accept any interference, including interference that may cause undesired operation of the device
MANUFACTURED BY
Bensussen Deutsch & Associates, LLC. (BDA, LLC.) 15525 Woodinville-Redmond Rd. NE Woodinville, WA 98072
BDAINC.com | POWERA.com
CONTACT/SUPPORT
For support with your authentic PowerA accessories, please visit PowerA.com/Support.
WARRANTY
2-Year Limited Warranty: Visit PowerA.com/support for details.
AUSTRALIAN WARRANTY STATEMENT
This product comes with guarantees that cannot be excluded under the Australian Consumer Law.
You are entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to have
the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure. If purchased within Australia or New
Zealand, this product comes with a one-year warranty from the date of purchase.
Defects in the product must have appeared within one year from the date of purchase, in order to claim the warranty. All warranty claims must be facilitated back through
the retailer of purchase in accordance with the retailer’s return policies and procedures. Any expenses incurred, as a result of returning the product to the retailer of
purchase are the full responsibility of the consumer.
AU WHOLESALE DISTRIBUTOR
Level 2, 2 Darling Street South Yarra, Australia VIC 3141
bluemouth.com.au
Email: support@bluemouth.com.au
+61 (3) 9867 2666
ADDITIONAL LEGAL
PowerA and the PowerA logo are trademarks of Bensussen Deutsch and Associates, LLC.
TM and © Bensussen Deutsch and Associates, LLC.
Nintendo Switch is a trademark of Nintendo. Licensed by Nintendo.
All rights reserved. All other trademarks are the property of their respective owners.
REGIONAL COMPLIANCE SYMBOLS
More information is available via web-search of each symbol name.
The WEEE (Waste of electrical and electronic equipment) symbol requires battery disposal outside of other household waste per local regulations. Contact your city
office, waste disposal service, or retailer for guidance.
CE is a certification mark that indicates conformity with health, safety, and environmental protection standards for products sold within the European Economic
Area.
The Regulatory Compliance Mark is a visible indication of a product’s compliance with all applicable ACMA (Australian Communications and Media
Authority) regulatory arrangements, including all technical and record-keeping requirements regarding the electrical safety and/or electromagnetic compatibility (EMC).
DECLARATION OF CONFORMITY
Hereby, Bensussen Deutsch & Associates LLC at 15525
Woodinville-Redmond Road NE, Woodinville, WA 98072 USA, declares that this wired controller is in compliance with Directive 2014/30/EU.
The full text of the EU Declaration of Conformity is available at the following internet address: PowerA.com/compliance
File Downloads
PowerA User Manual
Wired Controller for Nintendo Switch
Download [optimized]
Download
References
To Next Page
Loading...
