determine the minimum threaded length,
add the thickness of the fixture and the nut
/ washer thickness. The nut and washer
thickness is equal to the nominal thread
diameter. Do not over tighten threaded
parts. Maximum tightening torque values
are listed in the table below. Use of a nut
setter is recommended to reduce the possibility of over tightening
the fasteners. For critical applications, perform a job site test.
MAXIMUM TORQUE MAXIMUM TORQUE
F
OR 1/4" STUD (FT.-LBS.) FOR 3/8" STUD (FT.-LBS.)
24
INSTALLATION IN STEEL
The following guidelines are based on the installation of a
fastener in ASTM A 36 structural steel with the point fully
penetrating the steel member. Recommended steel material
thickness ranges from a minimum of 1/8" to a maximum of
3/8". For use in higher strength structural steel, applications
where the point does not penetrate the steel member, or a
thickness of steel greater than 3/8", job site performance tests
are recommended.
BASE MATERIAL THICKNESS
Steel base materials should be a minimum of 1/8" in thickness.
EDGE DISTANCE
For installations in A 36 steel, 1/2" is the recommended
minimum edge distance.
SPACING
The recommended minimum distance between fastenings is
1-1/2" center to center for installations in ASTM A 36 steel.
FASTENER LENGTH SELECTION IN STEEL
For permanent applications when using pins in steel, first
determine the thickness of the
fixture to be fastened. To this, add the thickness of the steel
base material plus a minimum of 1/4" to allow for proper point
penetration. This will be the minimum fastener shank length
required. Do not select a fastener length longer than that
required for the application. An excessively
long shank can burnish or polish the hole
created in the steel resulting in a reduction
in load capacity.
For removable applications with
threaded studs, the shank length required is
equal to the thickness of the steel base
material plus a minimum of 1/4" to allow
for proper point penetration. This will be the
minimum fastener shank length required.
Do not select a shank length longer than
that required for the application. An
excessively long shank can burnish or polish
the hole created in the steel resulting in a reduction in load
capacity. To determine the minimum threaded length, add the
thickness of the fixture and the nut / washer thickness. The nut
and washer thickness is equal to the nominal thread diameter.
Do not over tighten threaded studs, the maximum tightening
torque is listed in the table below. Use of a nut setter is
recommended to reduce the possibility of over tightening the
fasteners. For critical applications, perform a job site test.nut and
washer thickness is equal to the nominal thread diameter.
Do not over tighten threaded studs, the maximum tightening
torque is listed in the table below. Use of a nut setter is
recommended to reduce the possibility of over tightening the
fasteners. For critical applications, perform a job site test.
Powder Load Selection Guide
.27 CALIBER SAFETY STRIP
®
CAT. POWER LOAD STD. STD. MASTER WT./
NO. LEVEL COLOR SIZE BOX CTN. CTN. 100
50620 2 Brown .27 strip 100 1000 20000 .33
50622 3 Green .27 strip 100 1000 20000 .33
50626 4 Yellow .27 strip 100 1000 20000 .33
50630 5 Red .27 strip 100 1000 20000 .33
.27 CALIBER SAFETY STRIP
®
MASTER PACK
CAT. POWER LOAD STD. STD. MASTER WT./
NO. LEVEL COLOR SIZE BOX CTN. CTN. 100
50624 3 Green .27 strip 1000 - 20000 .33
50628 4 Yellow .27 strip 1000 - 20000 .33
50632 5 Red .27 strip 1000 - 20000 .33
Fastener Selection Guide
.300 HEAD DIAMETER DRIVE PINS
CAT. STD. STD. HEAD SHANK WT./
NO. SHANK LENGTH BOX CTN. DIA. DIA. 100
50012 1/2" K 100 5000 .300 .143 .5
50016 5/8" K 100 5000 .300 .143 .5
50022 3/4" 100 5000 .300 .143 .5
50026 1" 100 5000 .300 .143 .6
50030 1-1/8" 100 1000 .300 .143 .7
50032 1-1/4" 100 1000 .300 .143 .8
50034 1-1/2" 100 1000 .300 .143 .9
50036 1-3/4" 100 1000 .300 .143 1.1
50038 2" 100 1000 .300 .143 1.2
50040 2-1/4" 100 1000 .300 .143 1.2
50042 2-3/8" 100 1000 .300 .143 1.3
50044 2-1/2" 100 1000 .300 .143 1.4
50046 2-3/4" 100 1000 .300 .143 1.6
50048 3" 100 1000 .300 .143 1.9
.300 HEAD DIAMETER DRIVE PINS WITH TOP HAT
CAT. STD. STD. HEAD SHANK WT./
NO. SHANK LENGTH BOX CTN. DIA. DIA. 100
50136 1/2" K 100 5000 .300 .143 .5
50138 5/8" K 100 5000 .300 .143 .5
50140 3/4" 100 5000 .300 .143 .5
50144 1" 100 5000 .300 .143 .6
.300 HEAD DIAMETER STEP SHANK PINS
CAT. STD. STD. HEAD SHANK WT./
NO. SHANK LENGTH BOX CTN. DIA. DIA. 100
50158 3/4" Step Shank 100 1000 .300 .143/130 .5
50159 1" Step Shank 100 1000 .300 .143/130 .6
.300 HEAD DIAMETER DRIVE PINS -MASTER PACK
CAT. STD. STD. HEAD SHANK WT./
NO. SHANK LENGTH BOX CTN. DIA. DIA. 100
50980 1/2" K 1000 5000 .300 .143 .5
53300 5/8" K 1000 5000 .300 .143 .5
51040 3/4" 1000 5000 .300 .143 .5
51100 1" 1000 5000 .300 .143 .6
51160 1-1/4" 1000 5000 .300 .143 .8
51340 1/2" K TH 1000 5000 .300 .143 .5
53400 5/8" K TH 1000 5000 .300 .143 .5
51400 3/4" TH 1000 5000 .300 .143 .5
51520 1" TH 1000 5000 .300 .143 .6
K=Knurled TH=Top Hat
MODEL P3500 CAT. NO.52000/Deluxe Kit 52001/Blister Pack
4 P3500
@@@@@@
@@@@@@
@@@@@@
@@@@@@
ÀÀÀÀÀÀ
ÀÀÀÀÀÀ
ÀÀÀÀÀÀ
ÀÀÀÀÀÀ
@@@@@@
@@@@@@
@@@@@@
@@@@@@
ÀÀÀÀÀÀ
ÀÀÀÀÀÀ
ÀÀÀÀÀÀ
ÀÀÀÀÀÀ
@@@@@@
@@@@@@
@@@@@@
@@@@@@
ÀÀÀÀÀÀ
ÀÀÀÀÀÀ
ÀÀÀÀÀÀ
ÀÀÀÀÀÀ
@@@@@@
@@@@@@
@@@@@@
@@@@@@
ÀÀÀÀÀÀ
ÀÀÀÀÀÀ
ÀÀÀÀÀÀ
ÀÀÀÀÀÀ
@@@@@@
@@@@@@
@@@@@@
@@@@@@
ÀÀÀÀÀÀ
ÀÀÀÀÀÀ
ÀÀÀÀÀÀ
ÀÀÀÀÀÀ
@@@@@@
@@@@@@
@@@@@@
@@@@@@
ÀÀÀÀÀÀ
ÀÀÀÀÀÀ
ÀÀÀÀÀÀ
ÀÀÀÀÀÀ
@@@@@@
@@@@@@
@@@@@@
@@@@@@
ÀÀÀÀÀÀ
ÀÀÀÀÀÀ
ÀÀÀÀÀÀ
ÀÀÀÀÀÀ
yyyyyy
yyyyyy
yyyyyy
yyyyyy
To Next Page
Loading...
