Proaction A105QW - User Manual

Questions and Answers

J
jamespetersAug 14, 2025
Why is there excessive foam in the detergent drawer of my Proaction A105QW?
- C
  carl00Aug 14, 2025
  If you notice excessive foam in the detergent drawer of your Proaction Washer, it's likely due to using too much detergent or using the wrong type. To stop the foam, press the start/pause button. Dilute one tablespoon of softener in half a liter of water and pour it into the detergent drawer. After 5-10 minutes, press the start/pause button again. In future washes, use only detergents specifically produced for full automatic machines and ensure you're using the correct amount.
K
Kyle NealAug 17, 2025
Why my Proaction A105QW Washer does not operate?
- L
  Lauren HutchinsonAug 17, 2025
  If your Proaction Washer doesn't start, several things could be the cause. First, ensure the washer is properly plugged into the socket. Check your fuse to see if it is defective and change it if needed. Verify that there is electric power. Make sure you have pressed the start/pause button. Also, check that the program knob is not in the '0' (off) position, turn it to the desired setting. Finally, confirm that the door is completely shut until you hear a click.
N
nmartinAug 21, 2025
What to do if my Proaction A105QW does not receive water?
- G
  griffithrogerAug 21, 2025
  If your Proaction Washer isn't filling with water, start by checking that the water tap is fully open. Inspect the water inlet hose for any bends that might be restricting the flow. Also, the water inlet hose or the valve inlet filter may be obstructed. Clean the filters of water inlet hose and the valve inlet filters. Lastly, ensure that the door is properly closed; you should hear a click.
T
Thomas BowersAug 25, 2025
How to fix a Proaction A105QW Washer that is not draining water?
- S
  sdavisAug 25, 2025
  If your Proaction Washer is not draining water, check the drain hose for any obstructions or bends. Also, the pump filter may be obstructed. Clean the pump filter. Ensure that the clothes are spread inside the machine in an orderly and well-balanced manner.
M
matthewleeAug 27, 2025
How to stop my Proaction Washer from vibrating?
- C
  cassie10Aug 28, 2025
  If your Proaction Washer is vibrating, make sure the feet of your machine are adjusted. Also, check that the transportation screws are removed.
M
mfloydAug 31, 2025
Why is the washing result poor with my Proaction A105QW Washer?
- D
  Danielle OrtizAug 31, 2025
  If you're finding that your Proaction Washer isn't cleaning clothes effectively, consider whether your laundry is too dirty for the selected program; if so, select a suitable program. Also, the amount of detergent used may not be sufficient, use more detergent.
M
Margaret CoxSep 3, 2025
How to remove detergent residues from clothes after washing in my Proaction A105QW Washer?
- L
  Laura SandersSep 3, 2025
  If you notice detergent residues on your clothes after washing with your Proaction Washer, it may be due to insoluble ingredients in the detergent that form white stains. To resolve this, carry out an additional rinse cycle. Alternatively, you can eliminate the stains after drying with a brush.
R
Raymond MorganSep 6, 2025
What causes grey stains on clothes after washing in my Proaction Washer?
- C
  Cody RivasSep 7, 2025
  If you find grey stains on clothes washed in your Proaction Washer, these stains may be caused by oil, cream, or ointment. In the next wash, use the maximum amount of detergent recommended by the detergent producer.
T
thomasbrendanSep 10, 2025
Why is the spinning process delayed in my Proaction A105QW Washer?
- C
  Christopher FoxSep 10, 2025
  The spinning process might be delayed in your Proaction Washer because the unbalanced load control system is active. This system distributes clothes evenly before spinning. After your clothes are distributed, passage to spinning process will be realized. In the next washing process, place your clothes into the machine in a well-balanced manner.