To Next Page
W
wernerwilliamSep 13, 2025
What to do if rollers are cold when laminating with Professional Laminating Systems II?
- EEllen FieldsSep 13, 2025
If your Professional Laminating Systems Laminator rollers are cold when laminating, slow down the motor.
What to do if rollers are cold when laminating with Professional Laminating Systems II?
If your Professional Laminating Systems Laminator rollers are cold when laminating, slow down the motor.
What to do if my Professional Laminating Systems Laminator will not stop heating?
If your Professional Laminating Systems Laminator won't stop heating, unplug it and then contact technical support.
Why does my Professional Laminating Systems II display shows “Bat”?
If your Professional Laminating Systems Laminator shows "Bat" on the display, it indicates an incorrect voltage. Unplug the machine and contact technical support.
Why are there bubbles in edge seal parallel to the rollers in Professional Laminating Systems II?
If you have bubbles in the edge seal parallel to the rollers on your Professional Laminating Systems Laminator, it might be too hot. Try decreasing the temperature.
What to do if Professional Laminating Systems II has noise and runs at minimum?
If you're experiencing noise issues with your Professional Laminating Systems Laminator and it runs at a minimum, contact tech support.
What to do if my Professional Laminating Systems II display shows nothing?
If the display on your Professional Laminating Systems Laminator shows nothing, turn on the heat.
Why is there optical distortion in film parallel to rollers in Professional Laminating Systems II Laminator?
If you observe optical distortion in the film parallel to the rollers when using your Professional Laminating Systems Laminator, the following adjustments might help: * Increase speed if the motor is pulsating. * Reduce mandrel tension if the motor is pulsating. * Increase mandrel tension if the supply roll is bouncing. * Decrease tension if the film is stretching and rebounding. * Reduce roller pressure if it's too great.
Why don't mandrels hold film from slipping in Professional Laminating Systems II Laminator?
If the mandrels on your Professional Laminating Systems Laminator are not holding the film from slipping, it could be due to the wrong mandrel or a broken clip.
Why are there bubbles or air pockets in film only, not near edge, in Professional Laminating Systems Laminator?
If you're getting bubbles or air pockets in the film only (not near the edge) when using your Professional Laminating Systems Laminator, try the following: * Increase tension if the film is not running flat at the nip. * Decrease tension if the film is not running flat at the nip. * Increase pressure if there's not enough pressure for the application. * Decrease pressure if there's too much pressure, causing rollers to bend. Also, consider that the film might be defective.
Why is the film foggy on rollers and in lamination with my Professional Laminating Systems II Laminator?
If the film is foggy both on the rollers and in the lamination when using your Professional Laminating Systems Laminator, try the following: * Decrease the speed. * Increase the temperature. It's also possible that the film is defective.
Fields to record machine information like model, serial number, and purchase date.
Initial greeting and congratulations on the purchase of the laminator.
Essential safety guidelines and warnings for operating the laminator.
Necessary electrical connections and specifications for the laminator.
Overview of laminator capabilities and operational limitations.
Steps for unpacking the laminator and identifying included components.
Designated points on the laminator for safe lifting and handling.
Procedures for assembling the stand and mounting the laminator onto it.
Steps for assembling towers and installing the feed table.
Initial setup steps and familiarization with the laminator's control panel.
Correct installation of mandrels and adjustment of film tension and clips.
Aligning feed guides and adjusting roller pressure for optimal lamination.
Steps for assembling, installing, operating, and adjusting slitters.
Guidelines for selecting film, threading, and tuning the laminator for film.
Procedures for changing film rolls and removing stuck film.
Using fans, managing temperature, and adjusting roller pressure for optimal operation.
Best practices for two-sided and single-sided lamination techniques.
Procedures for laminating board stock and using cold lamination methods.
Steps for safely shutting down the laminator when not in use.
Routine cleaning of the laminator and application of basic lubricants.
Safety precautions and common causes of roller damage or failure.
Best practices for temperature, film use, and roller cleaning.
Initial troubleshooting steps and a list of common operational errors.
Addressing common film problems like fogging, bubbles, distortion, and waves.
Terms and conditions of the product warranty and steps for making a claim.
General| Brand | Professional Laminating Systems |
|---|---|
| Model | II Series |
| Category | Laminator |
| Language | English |