PSI NXG-Vision PS36L-P7 - User Manual

PS36L-P7
PS36L-P7
NOTE:
to PowerTec Solutions Models PS36L-K7 (Next Generation FTTx Micro UPS)
and all package accessories as listed below.
The reference to "NXG-Vision" within this User Manual refers
NXG-Vision INTRODUCTION
(when ordered with optional Universal )DC power supply and battery
back up device for Indoor 12Vdc Optical Network Terminals (ONT).
The NXG-Vision not only provides constant supply of DC power during
normal operating conditions, but offers battery backup power in case of
electrical power outage. NXG-Vision also provides customer facing
Network Interface Reset Intelligence to provide integrated ONT reset
technology designed to reduce Provider OPEX.
NXG-Vision is designed and intended for use as Desktop or Wall-mount
P
lea
s
e v
e
r
i
f
y a
l
l s
t
a
ndar
d c
ont
e
nt
s are a
cc
oun
t
ed f
or u
pon r
ece
i
p
t o
f
NXG
-
Vi
s
ion
. ST
AN
D
A
RD
: (
1) Power Supp
ly
/
C
h
arg
er; (
1) Li I
o
n B
a
t
ter
y P
ac
k
;
(1)
A
C Pow
er C
o
r
d; (1
) 7-
P
i
n C
on
n
ecto
r
; (
1
) U
s
e
r's M
a
nua
l
;
O
p
t
ion
a
l:
(1
) U
niver
s
a
l Wa
l
l M
o
unt E
nc
l
o
s
u
r
e w/ Cover.
N
OTE:
PS36L-P7
VISUAL INDICATORS
1
Battery
Color Red-
Service or replace battery or battery is not
installed in NXG-Vision.
,
2
Mute
Color-Yellow
Flashing Audible Alarm silenced for 24hrs.
Soid-Audible Alarm Silence Until manually
enable.
-
3
DC
Color Green-
NXG Vision is working off Standby Power.-
4
System
Status
Color- Green
NXG Vision is Recieving AC power load to
operate under normal conditions.
-
CONTROL SWITCHES
5
6
7
4
3
2
1
5
6
7
VISUAL AND AUDIBLE STATUS/ALARM SIGNALS
STATE
VISUAL
INDICATOR
AUDIBLE
INDICATOR
DESCRIPTION
Normal
System
Status
Indication On
Operating under normal AC
line power load and
conditions,
charges battery. Battery is
connected and in good
condition.
ON Battery
DC
Indicator On
AC line power failure
or AC cord
disconnection. NXG-
Vision is being supplied
with battery power.
Replace
Battery
Battery
Indicator On
1 2 second audible
indicator every 15
min.
/
Replace faulty or end of
life battery.
Battery
Missing
Battery
Indicator On
NXG Vision is operating
on AC line power only
without available
stanby power for outage
scenario. When battery
is removed from
unit, battery indicator will
illuminate after 5 sec.
-
Low Battery
DC Indicator
Flashes
1 2 second audible
indicator 4 times
per minute.
/
Battery has reached equal
to or less than 30%
remaining capacity on
battery discharge.
Review the following important safety warnings to avoid bodily injury or damage
to equipment during installation or operation of this device.
Read ALL instructions before attempting to install or operate this device.
This device is intended for indoor use only. To prevent the risk of fire or
eletrical shock, install in dry location free from damp or wet environment,
or potentially damp or wet environment.
Adhere to all acceptable operating environment limitations as listed to
prevent the risk of fire or electrical shock (see user specifications
within User's Manual)
Risk of fire or explosion if improper battery pack is installed and
attempted to operate with this device. Device is rated and approved for
use with PowerTec Solutions Internation Li Ion Battery Pack ONLY.
Follow User Manual instructions for proper installation and removal of
battery pack.
NO user-replaceable parts within this device. Do not remove cover for
any reason.
Allows NXG Vision to cold start power off
Battery Pack when AC line power is not
present and new or replacement pack is
connected,press and hold for 3 seconds.
-
Allows for DC line power reset of optical
Network terminal.Press and hold for 3
seconds to reset/reboot optical newwork
terminal.
Alarm
Silence
Cold
Start
N.I.R.
Reset
Disables Audible Alarm function. Press and release
to disable Audible Alarm for 24 hours. Press and hold
for 15 seconds to disable Audible Alarm indefinitely.
Press and hold for another 15 seconds in order to
re-enable Audible Alarm function.

Summary

Visual Indicators and Control Switches

Visual Indicators

Details the visual indicators on the NXG-Vision device, including battery color, mute, DC status, and system status.

Control Switches

Explains the functions of control switches like Alarm Silence, Cold Start, and N.I.R. Reset for device operation.

Status and Alarm Signals

Status and Alarm Descriptions

Summarizes device states (Normal, On Battery, Replace Battery) with visual/audible indicators and their meanings.

Connection Points

VAC Input and VDC;Telemetry Output

Identifies the connection points for AC power input and DC/Telemetry output on the bottom view of the model.

Installation and Battery Replacement

Installation Procedure

Step-by-step guide for installing the NXG-Vision battery pack and connecting the AC power cord to the device.

Battery Replacement Procedure

Instructions on how to replace the NXG-Vision battery pack safely while the device is operational.

Safety Warnings and Notices

Li Ion Battery Pack Safety

Crucial safety warnings regarding the Li-Ion battery pack, including handling, disposal, and storage precautions.

FCC Compliance and Interference

Information on FCC compliance for Class B digital devices and steps to correct potential radio frequency interference.

Technical Specifications

Input and Output Specifications

Details input voltage/frequency and output voltage/power capacity for the NXG-Vision device.

Battery and Surge Protection

Provides battery specifications, surge protection details, and device management features.

Physical and Environmental

Lists physical dimensions, weight, operating temperature, humidity, and storage conditions.

PSI NXG-Vision PS36L-P7 Specifications