Pulse Shower Spas Bali 1050 User Manual

6
Installation – New Construction
Extensive Remodel – New Finished Wall Surface
1. Prior to sheetrock, stub-out ½" hot and cold supply lines beyond
nishedwallsurface,4"oncenter.Forbestresults,attach90°
brassttings(availableatmosthardwarestores)tothestub-outs
maintaining¼"–½"ofspacebetweenthettingandnishedwall.
Theopenendofthe90°brassttingsshouldpointdownsothe
supply lines attach parallel to the wall.
1
2. For a person 5'8" – 6'2" we recommend the stub-outs be 40" above
nishedoor.
2
3. Before installation, make certain that water is COMPLETELY
TURNED OFF to both hot & cold supply lines of shower.
4a. Mark location of holes for the mounts, making sure holes are plumb.
For a person 5'8" – 6'2", we recommend placing the top hole of the
uppermountatapprox.71"abovenishedoor.
3
4b. Determine location for the lower mount. Measure the distance
between indents on the bottom edges of the two brackets on back
of ShowerSpa (approx. 35 ½"). Using this distance, measure down
from the top hole in upper mount to get the location of the top hole
in lower mount.
4c. Use the mounts to mark only one of the lower holes in each mount,
whichever is most convenient.
5. Before drilling holes, make certain that connecting to stub-outs
DOES NOT INTERFEREwithbacksideofShowerSpaanditisush
withnishedwallatdesiredmountingheight.
2
6. Drill ¼" holes through wall surface using a masonry bit. Drill slowly
through wall surface to avoid cracking and chipping. Insert anchors
and securely screw brackets to wall. Before connecting hot and cold
supply lines, hang the ShowerSpa on wall, check the height and
makesuretheShowerSpaisushagainstwallwithasecuret.
7. Connect hot and cold water supply lines to stub-outs—DO NOT
OVERTIGHTEN.BeforemountingtheShowerSpa,checkttingsto
make sure they are secure. Turn on water and check for leaks. When
ttingsareleak-free,mountShowerSpaonwall.
8. OPTIONAL—Seal around body of ShowerSpa with a bead of silicone.
DO NOT SEAL BOTTOM.
Retrot–ExistingShowerReplacement
NOTE—Inaremodelinwhichyouarenotreplacingthenishedwallsurface(tile,orbackingmaterial)itisadvisabletopurchaseaPULSEShowerSpa
model that covers the location of your existing valve assembly—either single handle or two-handle type. If your PULSE ShowerSpa model does not
cover this area, you will need to either choose another PULSE ShowerSpa model that does or make necessary repairs with appropriate materials
(i.e.wallboard,tile,berglass,etc).
1. TURN OFF WATER SUPPLY TO SHOWER. Typically there is a gate
valve where the water main enters the house. Turning the water
valveoathotwatertankdoesnotturnocoldwatersupplyline.
 2. Makecertainwateriscompletelyturnedotobothhot&cold
supply lines of shower. Turn shower valve on, both hot and cold, to
VERIFY WATER SUPPLY IS OFF. Open a sink faucet in the bathroom
in which you are installing the ShowerSpa to relieve any pressure and
help adequately drain shower supply lines.
3. Remove handle(s) and trim cover(s) of your existing shower valve,
exposing valve body in wall.
4. Locate hot and cold supply lines entering valve. Using a
reciprocating saw with sharp metal saw blade, cut existing valve out,
preserving threads of the supply lines entering valve. You should also
cut the riser within wall supplying the existing showerhead. Carefully
twist and remove valve.
5. Unscrew old showerhead from shower arm, then unscrew shower
arm from wall.
6. Water lines must be extended to the outside of wall cavity, 4" on
center.Forbestresults,attach90°brassttings(availableatmost
hardware stores) to the stub-outs maintaining ¼" – ½" of space
betweenthettingandnishedwall.Theopenendofthe90°brass
ttingsshouldpointdownsothesupplylinesattachparalleltothe
wall.
1
7a. Mark location of holes for the mounts, making sure holes are plumb.
For a person 5'8" – 6'2", we recommend placing the top hole of the
uppermountatapprox.71"abovenishedoor.
3
7b. Determine location for the lower mount. Measure the distance
between indents on the bottom edges of the two brackets on back
of ShowerSpa (approx. 35 ½"). Using this distance, measure down
from the top hole in upper mount to get the location of the top hole
in lower mount.
7c. Use the mounts to mark only one of the lower holes in each mount,
whichever is most convenient.
8. Before drilling holes, make certain that connecting to stub-outs
DOES NOT INTERFEREwithbacksideofShowerSpaanditisush
withnishedwallatdesiredmountingheight.
2
9. Drill ¼" holes through wall surface using a masonry bit. Drill slowly
through wall surface to avoid cracking and chipping. Insert anchors
and securely screw brackets to wall. Before connecting hot and cold
supply lines, hang ShowerSpa on wall, check the height and make
sureShowerSpaisushagainstthewallwithasecuret.
10. Connect hot and cold water supply lines to stub-outs—DO NOT
OVERTIGHTEN.BeforemountingtheShowerSpa,checkttingsto
make sure they are secure. Turn on water and check for leaks. When
ttingsareleak-free,mountShowerSpaonwall.
11. OPTIONAL—Seal around body of ShowerSpa with a bead of silicone.
DO NOT SEAL BOTTOM.
1
Additionalttingsorlongersupplylinesmaybenecessarydependingonyourspecicsituation.
2
The desired mounting height of ShowerSpa determines, or is determined by location of the ½" stub-outs.
3
The mounting height can vary depending on several factors (i.e. location of supply lines, interference from ShowerSpa plumbing, old valve access area,
personal preference, etc.)

Pulse Shower Spas Bali 1050 Specifications

General

Brand	Pulse Shower Spas
Model	Bali 1050
Category	Bathroom Fixtures
Language	English