The Nanosteamer Clinical is a facial steamer designed for skin care, offering various steam modes and aromatherapy capabilities.
Function Description:
The device primarily functions to provide steam for facial treatments. It features both hot and cold steam functions, as well as a "Smart Steam" mode that alternates between hot and cold steam. An aromatherapy function allows for the use of water-soluble essential oils to enhance the treatment.
- Hot Steam: Helps to open pores, hydrate, and purify the skin. It also relaxes pores, making them more receptive to moisture and subsequent treatments.
- Cold Steam: Helps to tighten pores, refresh the skin, and lock in moisture.
- Smart Steam Mode: A combination of alternating hot and cold steam, designed for maximum anti-aging benefits.
- Aromatherapy Function: Allows essence oils to penetrate the skin deeper when added to the aromatherapy basket.
Usage Features (Modes):
The Nanosteamer Clinical offers several pre-programmed modes, each with specific durations and steam types:
- Cleansing Mode: (4 minutes of hot steam) Designed for makeup removal and deep cleansing, to be used prior to any other function. The device automatically shuts off after 4 minutes.
- Cold Steam Mode: (60-70 minutes) Provides continuous cold steam. Users should adjust the distance of the steam to the skin.
- Hot Steam Mode: (2-3 minutes) Provides continuous hot steam. Users should adjust the distance of the steam to the skin. After hot steam, it's recommended to follow with skincare and additional treatments.
- Smart Steam Mode: (20 minutes total) Alternates between cold steam (3 minutes) and hot steam (3 minutes). The device automatically shuts off after 20 minutes.
- Hydration Mode: (Total duration not specified, but sequence is Hot 6 min, Cold 1 min, Hot 3 min, Cold 1 min, Hot 3 min, Cold 1 min) A sequence of hot and cold steam designed to hydrate dry skin and lock in moisture. The device automatically shuts off after completing the sequence.
- Oil-Control Mode: (Total duration not specified, but sequence is Hot 6 min, Cold 3 min, Hot 3 min, Cold 2 min, Hot 2 min, Cold 1 min) A sequence of hot and cold steam to help control oily skin types while locking in moisture. The device automatically shuts off after completing the sequence.
Preparation and Operation:
- Aromatherapy Basket: Remove the basket cover, add drops of water-soluble essential oils, and place the cover and basket back into the device.
- Skin Preparation: Fully remove any makeup, dirt, and oil with a face cleanser.
- Water Tank: Pop out the water tank by pressing the lid. Remove the water tank cap by twisting counter-clockwise. Fill the tank with 235ml of pure or distilled water. Place the cap back on and turn clockwise to close. Press the lid to place the water tank back into the Nanosteamer Clinical.
- Power On: Plug in the Nanosteamer Clinical.
- Mode Selection: Press the "M" button to choose the desired mode on the LED display.
- Steam Distance: Adequately adjust the distance between the skin and the steam. A distance of 25cm (9-10 inches) is recommended for other modes.
- Shut Off: The device will automatically shut off when the mode time is complete. To stop manually, press and hold the power button for three seconds. If there is low water, the power button will turn orange and blink for about 3 seconds before automatically shutting off.
- Post-Use: Hold down the power button to turn off the Nanosteamer Clinical and then unplug it.
Important Safety Instructions:
- Always unplug the appliance immediately after use.
- Do not use while bathing or near water.
- Do not place in or drop into water or other liquid.
- Unplug immediately if the appliance falls into water.
- Never leave the appliance unattended when plugged in.
- Close supervision is necessary when used by or near children or individuals with certain disabilities.
- Use only for its intended purpose.
- Do not operate if the cord, plug, or appliance is damaged, or if it has been dropped or submerged in water. Return to a service center for repair.
- Keep the cord away from heated surfaces and do not wrap it around the appliance.
- Never block air openings.
- Never use while sleeping.
Warnings & Safety:
- Turn off and unplug before adding water.
- Only use distilled water.
- Do not immerse any part of the device in water.
- Avoid direct heat and damp surfaces.
- Only water-soluble essential oils for aromatherapy.
- The aromatherapy basket heats up; avoid direct contact.
- Before first use on skin, run one cycle of water through and evaporate.
- Adjust distance for proper ventilation between steam and skin; STEAM IS HOT.
- Stop use and consult a physician if pain or discomfort occurs.
- Do not shake or move during use.
- Clean the aromatherapy basket after each use.
- Clean the outside with a damp towel, then a dry towel after each use.
- Avoid use if you have sensitive skin or a medical condition affecting your skin.
- Keep out of reach of children and pets.
- Unplug after each use, before cleaning, and before maintenance.
Important Technical Specifications:
- Voltage: 120V
- Frequency: 60Hz
- Power: 320W
- Water Tank Capacity: 235mL
Maintenance Features:
- Water Type: Only distilled water should be used. Do not add other liquids.
- Pre-Cleaning: Ensure the device is turned off and unplugged before adding water or cleaning.
- Hot Steam Distance: When using hot steam, maintain adequate distance from the face to avoid injuries.
- General Caution: Always exercise caution to prevent accidents.
- Submersion: Do not submerge the Nanosteamer Clinical in water.
- Power Supply: Use the correct supply voltage of 120V/60Hz.
- Chemicals: Do not add any chemical solvents or cleaners to the water tank.
- Power Cord: Keep the power cord away from hot surfaces. If damaged, it must be replaced by designated maintenance staff or an equivalent professional.
- Disassembly: Do not disassemble or install the Nanosteamer Clinical without permission.
- Troubleshooting Contact: For electrical equipment problems, contact support@puredailycare.com.
- Post-Use Cleaning: Unplug the power cord before cleaning. Do not use abrasive cleaners or corrosive liquids.
Cleaning the Nanosteamer Clinical (Recommended Weekly):
- Unplug the device and drain any remaining water.
- Pour 1 cup of a 50/50 vinegar & water solution into the water tank.
- Turn on Hot Steam Mode for approximately 10 minutes.
- Hold down the power button to turn off the device.
- Allow the device to cool for approximately 10 minutes, then drain the solution.
- Pour distilled water into the water tank to rinse out any residual vinegar smell.
Troubleshooting:
- Machine not heating up:
- Switch not turned on: Turn on the switch.
- Not connected to power supply: Connect to socket.
- Household power fuse broken: Reset or replace fuse.
- No steam or small steam:
- Low water: Fill with purified or distilled water.
- Tank not placed correctly: Make sure the water tank is pressed tightly.
- Scale deposits and dirt in the chamber: Follow cleaning instructions.
General
To Next Page
