28
4
3H OFF FUNCTION
When the heater is working and button
2222
is pushed, the heater will switch off automatically after three
hours of operation (after pushing the button). During the countdown period this setting can be de-activated by
pushing the button again. In the display the status of this function is shown.
G TURNING THE HEATER OFF
1. Press the ON / OFF button
2020
. The red lamp flashes for about 8 seconds and the heater is turned off. Always
check that the flame goes out.
G
The ventilator continues operating for about 3 minutes after turning off in order to cool the inside of the
heater. If you turn off the power earlier, uncontrolled symptoms can occur (release of smoke, smell etc.)..
H IN CASE OF PROBLEMS
The symptoms mentioned above are not faults and not abnormal. Check the list.
Symptoms Causes
While igniting
Igniting is tedious
Igniting takes about 45 seconds. After filling the tank, wait till the fuel
has reached the fixed tank. Repeat ignition 2 or 3 times.
Crackling sound This sound is made by the electric ignition.
White smoke This can happen if the fuel does not circulate past the burner properly
During ignition or
turning off
Smoke and an unpleasant smell during first use
That is the protective lacquer getting warm. This soon stops. Give the
space more ventilation.
The ambient temperature does not increase and the requested
temperature is higher.
The space is too large.
The flame glows red. The ambient air is damp or salty or it contains too many impurities.
The ambient temperature does not decrease and the requested
temperature is lower.
The heater is being used in a small insulated space or the outside tem-
perature is relatively high. Turn the heater off.
The displayed ambient temperature is not the same as indicated by
a thermometer.
This is because the displayed ambient temperature is an indication of
the average temperature of the space.
Small knocking noises when the heater is in operation or immedia-
tely after turning off.
This is the sound of the metal expanding.
Noise 8 seconds after turning off. A ticking sound: can occur when the heater cools off.
THE INFORMATION DISPLAY
The information display not only serves as an indicator of the (set) time and temperature (sections C, E, and F), it
also indicates any malfunctioning of the heater. The code on the information display tells you what is the matter:
Code Information Action
Time
----
The heater has been automatically turned off by a power
cut or bad connection.
Restore power or restore the connection. Press the ON / OFF
key
2020
again.
E01
An earthquake (magnitude 5 or more), strong vibrations or
a shock will ensure that the heater automatically
turns off. (The safety system against shocks has worked).
Make sure there are no combustible materials around the
heater, or fuel leakages. Press the ON / OFF key
2020
again.
E02
E03
The heater has been automatically turned off after a fault
or during ignition or due to the presence of water or dust
in the fuel filter or in the fixed tank.
Remove the water and the dust in the fixed tank. Clean
the fuel filter (see chapter L). Press the ON / OFF button
2020
again.
E07
An increase in ambient temperature has turned the heater
off. (The temperature monitoring system has worked).
Ventilate the space. Let the heater cool off. Press the ON /
OFF button
2020
again.
Filter
E09
The heater has been automatically turned off because the
hot air stream, the ventilator or the ventilator filter is bloc-
ked or hindered by something. (The safety system against
overheating has worked).
Remove obstacles from the ventilator opening. Clean the
ventilator filter (see chapter L) Press the ON/OFF button
2020
again. If the problem occurs again after taking the above
measures, contact your dealer.
E13
The heater has been turned off in a closed space. (The
safety system against incomplete combustion has worked).
Ventilate the space and press the ON / OFF button
2020
again.
Ensure the space is sufficiently ventilated.
The ON indicator
flashes. Err lights up
The heater has automatically stopped because the ON / OFF
button was kept pressed in or was blocked.
Remove obstacles around the buttons of the display panel.
Press the ON/OFF button
2020
again.
F00 – F30 Poor functioning. Heater needs maintenance
Note the messages displayed and turn the heater off. Con-
tact your dealer.
To Next Page
Loading...
Need help?
General
