QUICK DAM FLOODGATE QDFG45

To Next Page

THE NEXT GENERATION IN FLOOD PROTECTION

FREQUENTLY ASKED QUESTIONS

What are Flood Gates made from?

1in Steel tube frame for structure & support, .125in steel plates for support & take the weight

of the water, 1.5ton scissor jack for expansion and a neoprene sleeve for a water tight seal. Also

included in the package will be an expansion tool, ratchet wrench & instruction manual.

Can I still use the entrance while the Flood Gate is in place?

Yes, simply open the door & step over, while maintaining ood protection.

What sizes do the Flood Gates come in?

We currently offer 5 sizes each of which expands 5in & all offering ood protection up

to 26.5in high. The 5 sizes range from: 25in-30in, 30in-35in, 35in-40in, 40in-45in,

45in-50in.

How long does it take to install the Flood Gate?

As long as your reveal is clean & ready, it should only take 5 minutes, expand jack & 4 bolts

on the bottom.

Have the Flood Gates been tested?

Yes, the Flood Gates were designed, developed, tested & patented in the UK

& also patented in the US. Testing was performed in the UK & passed British

Kite Mark testing to prevent ood water entering up to 24in. The US Flood

Gates are manufactured under the same UK standards.

Where can Flood Gates be used?

In any entryway that Flood Gates can t into. This can include: Residential, Commercial,

Retail, Government, Power & Nuclear, Hospital, Hotel, Condo's & Apartments & more.

Are custom sizes available?

No not normally, as there is quite a bit of engineering involved & custom neoprene sleeves

that would have to be made, which would make the cost too signicant for single units.

What if my door is wider than 50in?

Stanchions are available to join multiple units together*. The Stanchion Base will need to

be installed in the ground & left as a ush surface until needed. (See instruction manual for

more details)

Can I connect multiple units together?

Yes, using the stanchion set list above. (See instruction manual for more details)

Do the sleeves come in different colors?

Not at this time. Orange is currently the only colored sleeve.

Can I get replacement sleeves?

Yes, should your outer sleeve become damaged, replacements are available online at

quickdams.com.

Can I get them any taller?

Flood Gates are only available 26in high at this time.

quickdams.com

Flood water

comes from

this side

Ground

UNDERGROUND

Upright Stanchion

Base

Stanchion and Base Installation:

Kitemark Tested

& Approved

Need help?

Do you have a question about the QUICK DAM FLOODGATE QDFG45 and is the answer not in the manual?

Summary

Flood Gate Materials and Components

Flood Gate Construction

Flood Gates are constructed with a 1-inch steel tube frame, .125-inch steel plates, and a 1.5-ton scissor jack with a neoprene sleeve.

Flood Gate Sizes

Flood Gates are available in five sizes, expanding 5 inches, offering flood protection up to 26.5 inches high.

Flood Gate Testing and Approval

Flood Gates were tested and patented in the UK and US, passing British Kite Mark testing for flood water prevention up to 24 inches.

Applications for Flood Gates

Flood Gates can be used in various entryways including residential, commercial, retail, government, and hospitality settings.

Custom Sizes and Availability

Custom sizes are not normally available due to significant engineering and manufacturing costs for single units.

Joining Multiple Flood Gates

Multiple units can be joined using available stanchions, with a stanchion base needing ground installation.

Flood Gate Sleeve Colors

Currently, Flood Gate sleeves are only available in orange.

Replacement Flood Gate Sleeves

Replacement outer sleeves are available for purchase online at quickdams.com.

Flood Gate Height Limitation

Flood Gates are currently only available at a height of 26 inches.

Flood Gate Installation and Usage

Flood Gate Installation for Outward Opening Doors

For outward opening doors, the Flood Gate must be installed on the inside to ensure the jack faces away from water.

Door Frame Alterations for Installation

Minimal alterations are needed for smooth reveal areas; thin spacers and silicone caulk can level uneven surfaces.

Flood Gate Installation in Window Frames

Flood Gates can be installed in window frames if there is sufficient reveal and the window can be opened from the inside.

Correct Flood Gate Installation Orientation

The solid outer neoprene sleeve must face oncoming water for a secure seal and to prevent seepage.

Flood Gate Maintenance

After each use, hand wash the sleeve, wipe the frame, and grease moving mechanisms, operating the jack to distribute grease.

Flush Mount Door Frame Solutions

Side Rails can be added to flush mount door frames to hold the Flood Gate in place.

Flood Gate Storage

Store Flood Gates upright in a cabinet or closet, placing sleeves together to protect the jacks.

Stacking Flood Gates

Flood Gates should not be stacked on top of each other as this can cause damage to the jacks.

Transporting Multiple Flood Gates

A Flood Gate Cart is available for the ease and speed of storage and deployment of multiple units.

Stanchion Width Addition

Allow approximately 0.75 inches when calculating width needed for stanchions.

Sliding Door Installation

Sliding doors often lack depth; corner stanchions or side rails can create a secure area for gates outside.