NATIONAL INTERAGENCY INCIDENT COMMUNICATIONS DIVISION
THALES 25 PORTABLE RADIO (RACAL) ANALOG CHANNEL PROGRAMMING
Page 1 of 4
RACAL ANALOG CHANNEL PROGRAMMING
RACAL ANALOG CHANNEL PROGRAMMING GUIDE
1.
Select a channel for programming by rotating the Channel Select Knob to one of the sixteen rotary positions.
2.
Press the "
ENTER
" key to bring up the Main Menu screen.
(See Figure 1)
3.
Scroll up/down using the "
O
" and " " (
up/down arrow keys
) to select "
PROGRM
" and press the "
ENTER
" key.
4.
Enter a 6-Digit Password if requested and press the "
ENTER
" key.
Note: NIFC password is "000000".
5.
Scroll up/down and select "
CHANEL
" and press the "
ENTER
" key to program
Channel Parameters
.
(See Figure 2)
6.
Scroll down and select "
TAG
" and press the "
ENTER
" key.
(See Figure 3)
Change the channel name/label using the keypad and press the "
ENTER
" key when complete.
Note: "ID" cannot be changed, it is automatically updated when programming a channel.
7.
Scroll down and select "
MODE
" and press the "
ENTER
" key to program the
Channel Mode
.
(See Figure 4)
Select either "
ANALOG
" or "
DIGITAL
" and press the "
ENTER
" key.
Note: NIFC Default is "ANALOG" for all channels.
8.
Scroll down and select "
B/W
" and press the "
ENTER
" key to program the
Channel Bandwidth
.
(See Figure 4)
Select either "
25Khz
" or "
12.5Kh
z" and press the "
ENTER
" key.
Note: 25Khz= Wide-Band, 12.5khz= Narrow-Band.
Note: NIFC Default is "12.5 Khz" for Narrow-Band operation.
9.
Scroll down and select "
ENCRPT
" and press the "
ENTER
" key to program
Encryption. (See Figure 5)
Select either "
ENABLD
" or "
DISABD
" and press the "
ENTER
" key.
Note: If Encryption is enabled, a key must be loaded first into the radio with the PC Programmer.
Note: NIFC Default is " DISABD"
10.
Scroll down and select "
RX
" and press "
ENTER
" key to program the
RX Frequency
.
(See Figure 6)
Enter a valid RX frequency from 136-174 Mhz using the keypad and press the "
ENTER
" key.
11.
Scroll down and select "
RX SQMD
" and press the "
ENTER
" key to program the
RX Squelch Mode
.
(See Figure 7)
Select either "
NOISE
", "
DCS
", "
CTCSS
", or "
NONE
" and press the "
ENTER
" key.
Note: If "Noise" is selected, the program will proceed with the Squelch Adjust parameter ( SQ=), select a squelch
setting and press "ENTER" when done; this setting opens the squelch with any corresponding analog signal. If
"CTCSS" is selected, the program will proceed with a SUB Audible Tone menu, select a tone from the menu by
scrolling through and then press "ENTER"; this sitting will open the squelch with any corresponding analog signal
that contains the correct "CTCSS" tone. If "DCS" is selected, the program will proceed with the Digital Coded
Squelch tone menu, select a tone from the menu by scrolling through and then press "ENTER"; this setting will
open the squelch with any corresponding analog signal that contains the correct "DCS" tone. If "None" is selected,
squelch will be open at all times ( Constant Open Squelch).
Note: NIFC Default is "Noise" with a "SQ" setting of 8.
12.
Scroll down and select "
TX
" and press the "
ENTER
" key to program the
TX Frequency
.
(See Figure 8)
Enter a valid TX frequency from 136-174 Mhz using the keypad and press the "
ENTER
" key.
13.
Scroll down and select "
TX SQMD
" and press the "
ENTER
" key to program the
TX Squelch Mode
.
(See Figure 9)
Select either "
DCS
", "
CTCSS
", or "
NONE
" and press the "
ENTER
" key.
Note: If "CTCSS" is selected, the program will proceed with a Sub Audible Tone menu, select a tone from the menu
by scrolling through and press "ENTER" ; this sitting will include a " CTCSS" tone on the analog transmit signal.
IF "DCS" is selected, the program will proceed with a Digital Coded Squelch menu, select a tone from the menu by
scrolling through and then press "ENTER"; this setting will include a " DCS" tone on the analog transmit signal.
If "None" is selected, no tones are sent out on the analog transmit signal.
Note: NIFC Default is "None".
14.
Scroll down and select
"LO PWR
" and press "
ENTER
" to program the
Low Power Setting
.
(See Figure 10)
Select either "
0.1
", "
0.5
", "
1.0
", "
2.0
", or "
5.0
" Watts for low power setting and press the "
ENTER
" key.
Note: NIFC Default for Low Power is 1.0 Watts.
15.
Scroll down and select "
HI PWR
" and press the "
ENTER
" key to program the
High Power Setting
.
(See Figure 10)
Select either "
0.1
", "
0.5
", "
1.0
", "
2.0
", or "
5.0
" Watts for high power setting and press the"
ENTER
" key.
Note: NIFC Default for Hi Power is 2.0 Watts.
16.
If screen reads "
SAVE CHANNEL
", select "
YES
" to save. If not, channel information was stored and you can select
another channel using the channel select knob and continue programming other channels or press "
ESC
" a few
times to return to the main display.
Figure 1
Figure 3
Figure 2
Figure 4
Figure 5
Figure 6
Figure 7
Figure 8
Figure 9
Figure 10
NIICD RADIOS ONLY 2007/J.Lopez
To Next Page
Need help?
General