Ranger 90032 - Page 5

11 pages

Save Page as PDF

To Next Page

To Next Page

To Previous Page

To Previous Page

Loading...

Ranger

Pressure

Infusor

and

Power

Pack

Introduction

Indications

for

Use

The

Ranger

pressure

infusor

is

intended

to

provide

pressure

to

LV.

solution

bags

when

rapid

infusion

of

liguids

is

reguired.

Description

of

the

Pressure

Infusor

and

Power

Pack

Pressure

Infusor

The

Ranger

pressure

infusor

can

be

used

with

the

Ranger

blood/fluid

warming

unit

and

Ranger

standard

and

high

flow

disposable

set

and

irrigation

warming

sets.

The

infusor

can

accept

solution

bags

ranging

from

500

mL

to

1000

mL.

The

pressure

infusor

includes

a

fitting

that

allows

it

to

be

connected

to

the

regulator

of

a

compressed

air,

COa,

or

nitrogen

tank

to

provide

a

static

operating

pressure

of

250-350

mmHg,

Under

flow

conditions,

the

pressure

infusor

delivers

a

maximum

fluid

pressure

of

300

mmHg,

Note:

The

Ranger

Model

90083

is

calibrated

using

a

1000

mL

solution

bag

that

is

approximately

6"

x

10"

(152.4

x

254

mm).

The

Ranger

Model

90032

is

calibrated

using

a

1000

mL

solution

bag

that

is

approximately

4"

x

11"

(101.6

x

279.4

mm).

The

outlet

pressure

of

the

fluid

will

vary

with

the

surface

area

and

volume

of

the

solution

bag.

If

solution

bags

of

different

sizes

are

used,

the

pressure

of

the

fluid

should

be

checked

by

contacting

Arizant

Healthcare

Inc.

Technical

Support.

The

Ranger

pressure

infusor

has

no

user-adjustable

controls.

The

user

places

an

IV.

solution

bag

behind

the

bag

retainer

and

against

the

inflation

bladder

located

inside

the

pressure

infusor.

When

the

infusor

is

attached

to

an

external

power

source,

turning

the

infusor

on inflates

the

inflation

bladder

and

maintains

pressure

on

blood and

LV.

solution

bags.

Turning

the

infusor

off

while

pressing

on

the

bladder

quickly

deflates

the

bladder.

Power

Pack

The

power

pack

provides

a

dedicated

power

source

for

the

pressure

infusor.

The

power

pack

is

electrically

powered

(Model

90033:

110-120VAC,

50/60

Hz

or

Model

90031:

220-240

VAC,

50/60

Hz).

The

pressure

infusor

will

provide

a

static

operating

pressure

of

250-350

mmHg

when

connected

to

the

power

pack.

Under

flow

conditions,

the

pressure

infusor

delivers

a

maximum

fluid

pressure

of

300

mmHg.

WARNINGS

e

Never

infuse

fluids

if

air

bubbles

are

present

in

the fluid

line,

as

air

embolism

may

result.

»

‘This

product

is

designed

for

pressure infusion

only.

CAUTION

e

Do

not

sterilize

the

pressure

infusor

or

power

pack.

e

Do

not

leave

the

infusor

door

open

while

the

unit

is

turned

on;

otherwise,

the

LV.

bag

may

fall

out

and

the

infusor’s

bladder

may

disengage

from

the

unit.

Arizant

Healthcare

Inc.

|

|

JI

그

그

기

그

|]

그

그

|]

기

그

|

|

|

Table of Contents