RCI 9212i Installation Guide

©2013 RutheRfoRd contRols • www.RutheRfoRdcontRols.com
USA: 2517 SQUADRON COURT, SUITE 104, VIRGINIA BEACH, VA 23453 • CANADA: 210 SHEARSON CRESCENT, CAmBRIDGE, ON N1T 1j6
PHONE • 1.800.265.6630 • 519.621.7651 • FAX: 1.800.482.9795 • 519.621.7939 • E-mAIl: SAlES@RUTHERFORDCONTROlS.COm
IS9212i
Pcn13031
R04/13cA
INSTALLATION
9212i
Stand-Alone Keypad
Instructions
Features:
•4IndependentOutputs
•4IndependentTimers
•AllOutputsAssignablebyCode
•Onboard5AmpFormCRelay
•120Users
•RemoteTriggeringInput
•KeypadProgrammable
Memory
Non-volatileEEPROMmemorymeansyourcodesand
programmingwillbetherewhetheryouremovepowerfor
5minutesor5years.
Programming
Allprogrammingisaccomplishedentirelyfromthe
frontofthekeypad.LEDorSounderguidancemakes
programmingeasy,andchangingcodesamatterof
secondsforanauthorizeduser.
Codes
TheRCIkeypadsallowupto120individualusercodes
tobevalid.Codesmaybefrom1-6digitsinlength
anddigitsmayberepeated.TheMasterCodeisalways
assignedtouserlocationone(1).
Main Relay
Thisisa5Amp(10Ampsurge)Form-Crelaywhichcan
betoggledortimedfrom1to90seconds-bycode.
Auxiliary Outputs
Auxiliaryoutputscanbeindividuallytimedfrom1to90
secondsoractasatoggleswitch,andmaybetriggered
individuallyorincombination-bycode.Thethreeauxiliary
outputsprovidea50mAsinktogroundwhenactivated.
Remote Triggering Input
ThisnormallyopenloopthatbydefaultoperatestheMain
Relayuponactivationandcanbeprogrammedtotrigger
anycombinationofoutputs.Uponamomentaryclosure,
theselectedoutputswillenergizefortheirprogrammed
time.Themainrelay(ifselected)willenergizeforthe
sametimeperiodastheMasterCode.Thisfeatureis
especiallyusefulwhencontrollinganelectriclocking
device.
Keypress Feedback / Audible Keypress
TheRCIkeypadswillacknowledgeakeypressby
momentarilyilluminatingtheyellowLED.Thiscanbe
turnedoffthroughprogramming.
Keypad Active Output
TheRCIkeypadscanbeprogrammedtoenergizea
voltageoutputwheneverakeyistouched.Thiscanbe
usedtoturnonaccessoriessuchaslights,CCTVcamera,
ornotifyaguard.
Auto-Entry
Thisfeatureisusedwhentheneedforthecodenotto
befollowedbythe*keyisdesired.Theuseronlyneeds
toentertheircodenumberandtherelaywillactivatefor
theprogrammedrelaytime.Tousethisfeature,theuser
codesmustbethesamelengthasthemastercode.
Technical Notes:
ToavoidESD(Electro-StaticDischarge)frominterfering
withtheoperationoftheRCIkeypad,groundthenegative
terminalofthekeypadtoearthground.Ifthepower
supplycannotbegrounded,thenthecaseshouldbe
grounded.For24VDCoperation,removejumperJ2(see
Fig.5).
Packing Checklist:
9212iKeypad
Ten(10)ConductorWiringHarness(1)
SlottedScrews(2)
SecurityScrews(2)
Installation
Diode(1)
NOTE:Aswithanyelectronicproduct,the9212imaybesubjecttoirregularitiesintheACpowerline.Thiscancausemalfunctionorunstableoperation.
Connectingthe9212itoasuitableDCpowersupplywilllimittheeffectsofACfluctuationonthekeypad.
Voltage Current Rating Temperature Output
 12-24VAC/VDC @12VDC 8mAtyp–35mAw/relayenergized -20°Fto130°F(-28°Cto54°C) Mainrelay:5A;form-C@24VDC;10Asurge
  @24VDC 16mAtyp–45mAw/relayenergized  Outputs2-4are50mAnegvoltageoutputs

RCI 9212i Specifications

General

Type	Keypad
Operating Temperature	-20°C to +70°C (-4°F to +158°F)
Dimensions	120mm x 80mm x 25mm (4.72" x 3.15" x 0.98")
Weight	150g (5.3 oz)
Backlight	Yes
Operating Voltage	12V DC
Relay Contact Rating	1A @ 30V DC
Power Supply	12V DC
Number of Keys	12