The REDMOND RFH-4204 Ceramic Fan Heater is a domestic appliance designed for comfortable and efficient heating. It combines original technical solutions with modern technologies, offering high power and wide functionalities. The ceramic heating element is a key feature, providing comfortable heating without the problem of "burning oxygen." The oscillating function allows for quick and even heating of a room.
Important Technical Specifications:
- Model: RFH-4204
- Power: 1500 W
- Voltage: 220-240 V~50/60 Hz
- Type of control: Electronic
- LCD Display: Yes
- Auto climate control: Yes
- Type of heating element: Ceramic
- Oscillating function: Yes
- Quantity of modes: 2
- "High" mode: 1500 W
- "Low" mode: 750 W
- Heating area: Less than 15 m²
- Overheat protection: Yes
- Noise level: Less than 60 dB
The manufacturer reserves the right to introduce modifications to the design, complete set, and technical data of the device for continuous product improvement without additional notification.
Usage Features:
Before Operating:
For your own safety, it is crucial to read these instructions carefully before using the appliance. Proper use will ensure a long service life.
- Intended Use: This appliance is intended for domestic use only and not for industrial purposes. It is not designed for use by persons (including children) with reduced physical, sensory, or mental capabilities, or lack of experience and knowledge, unless supervised or instructed by a person responsible for their safety. Children should be supervised to ensure they do not play with the appliance.
- Placement: Always place the heater on a firm, stable, flat, and level surface to prevent overturning. Ensure the power source conforms to the electrical requirements of the heater.
- Extension Cords: Avoid using extension cords if possible, as they may overheat and pose a fire risk. If an extension cord must be used, minimize the risk by ensuring it is VDE listed, a minimum H05VV-F 2*0.75MM^2, and rated not less than 2070 watts. Never use a single extension cord to operate more than one heater.
- Safety Precautions:
- Do not operate the heater with a damaged cord or plug, or if it malfunctions, has been dropped, or damaged. Return it to an authorized service center for examination or repair.
- Unplug the power cord before servicing or moving the heater, and always unplug it when not in use. Do not rely on the ON/OFF switch as the sole means of disconnecting power.
- Do not insert fingers or foreign objects into any ventilation or exhaust opening, as this may cause electric shock, fire, or damage.
- To prevent fire, do not block air intakes or exhaust openings. Do not place the heater on soft surfaces like a bed where openings may become blocked.
- Locate the power cord so that the heater or other objects are not resting on it. Do not run the power cord under carpeting or cover it with throw rugs. Arrange the power cord away from room traffic to prevent tripping.
- The heater becomes hot during use. To avoid burns, do not let bare skin touch hot surfaces. Always use the handle when moving it. Keep combustible materials (furniture, pillows, bedding, papers, clothes, curtains) at least 900mm from the front and at least 300mm from the sides and rear.
- The heater contains hot and arcing or sparking parts inside. It must NOT be used in potentially dangerous locations such as flammable, explosive, chemical-laden, or wet atmospheres. This heater is intended for general use ONLY.
- This heater is not intended for use in wet or damp locations. Never locate it where it may fall into a bathtub or other water container.
- Do not use the heater outdoors.
- WARNING: To reduce the risk of fire or electric shock, do not use this heater with any solid-state speed control devices.
Before First Use:
- Carefully remove the heater from its bag and carton.
- Place the heater on a firm, level surface.
Operating Instructions:
- Place the heater on a firm, level surface. Plug the cord set into a suitable electrical outlet.
- Installation Distance: During installation, ensure the heater is positioned at a safe distance from interior objects: not less than 30 cm from the back and lateral faces, and not less than 90 cm from the front.
- Power On/Off: Set the main power to "OFF." Plug the cord set into a 220-240V ~A.C. electrical outlet. Press the "ON/OFF" button to start. A 'Beep' sound and a blue light will indicate power to the unit. The blue light will remain on until the main POWER switch is turned OFF and the heater is unplugged.
- Mode Selection: Press the "Mode" button to select the desired heating mode:
- One touch: "High" mode (1500 W)
- Double touch: "Low" mode (750 W)
- Triple touch: "AUTO" mode
- AUTO Mode: If "AUTO" mode is selected, set the desired temperature using the "Up" (5) and "Down" (7) keys. The LCD display (8) will show the set temperature. Once the temperature is set, the LCD will revert to displaying the current room temperature. In "AUTO" mode, the heater will automatically turn on and off to maintain the set temperature.
- Oscillation Function: Press the "OSC" button (6) to activate the oscillation function, allowing the heater to oscillate side to side. Press it again to stop oscillation. When the desired room temperature is reached, the oscillation function will stop. It will automatically resume when the temperature drops.
- Timer Mode: This function works in any mode. The timer allows you to set the length of operation from 0 to 8 hours, after which the heater will automatically turn off.
Maintenance Features:
Cleaning and Maintenance:
- Before cleaning, ensure the appliance is disconnected from the power supply and has completely cooled down.
- Clean the appliance body with a damp cloth soaked in a soapy solution.
- Avoid using abrasive cleaning agents.
- Allow the appliance to air dry naturally before resuming operation.
Troubleshooting:
| Trouble | Probable cause 200
RED
To Next Page
Need help?
General