RELAX-A-MIST CR-12 - User Manual

CN
2016
QUALITY STEAM BATH EQUIPMENT
R E L A X
M IST
A
®
1
www.relax-a-mist.com1-800-Y-U-STEAM
(1-800-987-8326)
1. GENERAL INFORMATION (See Steam Generator Selecon)
STEAM GENERATOR LOCATION
         
outside of, but within 20 feet of the shower or steam room,
where the steam pipe can be installed without the possibility of a



MUST be easily accessible should service be required in the
       
         
        Fig. 1.
1 lb) in the boiling tank than a longer route with many elbows.
      
materials, tools and methods. Depending on wall thickness,
custom sized nipples may need to be fabricated by the plumber
or purchased from a local hardware store. It is important to
install the steam diusers in an area where a person cannot
be burned from the hot steam exing the diusers. The steam


See Steam Piping to Bath or Shower, CAUTION 1-3, and Fig. 2.
USE ONLY RELAX-A-MIST® FACTORY SUPPLIED PARTS
TWO 3/4” STEAM DIFFUSERS
INSTALLATION INSTRUCTIONS
MODELS CR-12 & CR-14
208 VOLTS 3 PHASE
CONTROL
CORD SET
CR-12 OR CR-14 STEAM GENERATOR
WATER
INLET
STEAM PIPING AND STEAM DIFFUSER
(To and in the steam room)

and must be manifolded to two 3/4 inch pipes at the steam
          
        
         
elbows will, in most cases, maintain a lower pressure (less than
CAUTION: There is to be NO RESTRICTION in the STEAM
PIPE BETWEEN the STEAM GENERATOR and the STEAM
DIFFUSERS that would in any way cause PRESSURE to
build in the STEAM GENERATOR. INSTALL the STEAM
DIFFUSERS 12 INCHES above the nished oor, in a
LOCATION where the STEAM WILL NOT BURN anyone.
TIMER SWITCH (Steam Generator Control)
The Quick Touch Timer can be located inside or outside the steam

      
CAUTION 11.
DRAIN VALVE OPTION
A 3/4 inch copper, female adapter (located below the water
         
         
the steam generator (purchased separately). See Fig. 2.
QUICK TOUCH TIMER
CONTROL
(PACKAGED INSIDE
ELECTRICAL BOX)
Fig. 1
QUALITY STEAM BATH EQUIPMENT
REL AX
MIST
A
®
QUALITY STEAM BATH EQUIPMENT
REL AX
MIST
A
®
QUALITY STEAM BATH EQUIPMENT
REL AX
MIST
A
®
QUALITY STEAM BATH EQUIPMENT
R
E
L
A
X
M
IS
T
A
®
STEAM LINE 3/4”
TEE 1” TO 3/4”
UNION 1”
DRAIN
QUALITY STEAM BATH EQUIPMENT
R
E
L
A
X
M
IS
T
A
®
STEAM LINE 1”
STEAM
LINE 3/4”
TEE 1” TO 3/4”
UNION 1”
DRAIN
Fig. 2
Option #1
Option #2

Summary

1. GENERAL INFORMATION

STEAM GENERATOR LOCATION

Details the required location for the steam generator, focusing on accessibility and environmental factors.

STEAM PIPING AND STEAM DIFFUSER

Outlines requirements for steam pipe material, size, and routing to the steam diffusers within the steam room.

TIMER SWITCH (Steam Generator Control)

Explains the placement and function of the Quick Touch Timer for controlling the steam generator.

DRAIN VALVE OPTION

Describes the option to install a drain valve for the steam generator, essential for maintenance.

2. ROUGH-IN

WATER SUPPLY

Covers water supply requirements including pressure, shut-off valve, and potential water treatment needs.

DRAIN VALVE OPTION

Details the installation of a 3/4 inch rigid copper pipe for draining the steam generator to a suitable drain.

ELECTRICAL - WATTS, WIRE AND FUSE SIZES

Specifies electrical requirements like voltage, wattage, wire gauge, and fuse/breaker sizes for safe operation.

STEAM PIPING TO BATH OR SHOWER

Guides on installing steam pipes, diffuser fittings, and ensuring proper orientation for efficient steam distribution.

3. FINAL INSTALLATION

ELECTRICAL (According to Local Electrical Code)

Details connecting the power supply wires to the steam generator's electrical connection box, using knock-outs.

WATER SUPPLY (According to Local Plumbing Code)

Explains connecting the water inlet using a supplied garden hose adapter and 3/8 inch tubing.

DRAIN VALVE OPTION (According to Local Plumbing Code)

Covers installing a shut-off valve within 1 foot of the steam unit for the drain line, must be closed during operation.

TIMER PRETEST

Provides step-by-step instructions for testing the Quick Touch Timer before completing the final electrical installation.

FINAL STEAM PIPE INSTALLATION

STARTUP INSTRUCTIONS

STEAM GENERATOR SELECTION

WARRANTY POLICY

AUTHORIZED SERVICE DEPOTS

Lists authorized service depots for warranty repairs and provides contact information for assistance.

RELAX-A-MIST CR-12 Specifications

General

Brand	RELAX-A-MIST
Model	CR-12
Category	Iron
Language	English