REMS E-Push 2 - Page 24

24
eng eng
5.2 Fault:
Compressor will not start although there is low or no pressure in the compressed air tank (see the display on the compressed air tank pressure gauge
(Fig.4 (30)).
Cause:
Remedy:
●
Compressor emergency stop button (Fig.4 (29)) is switched off.
●
Switch on compressor by pulling out the emergency stop button.
●
REMS Multi-Push defective.
●
Have the REMS Multi-Push checked/repaired by an authorised REMS
customer service workshop.
5.3 Fault:
The necessary minimum fl ow velocity is not achieved in the fl ushing program.
Cause:
Remedy:
●
Stop tap of the house connection is only partly open.
●
Fully open the stop tap.
●
Fine fi lter (Fig. 3 (12)) is contaminated.
●
Clean or change the fi ne fi lter and fi lter cartridge.
●
Not enough tapping points opened.
●
Open the appropriate number of tapping points.
●
Hoses connected incorrectly.
●
Connect hoses as shown in Fig. 3.
●
Wrong defaults entered.
●
Check defaults, correct if necessary. Restart the program.
●
Valves blocked, considerable, irremovable encrustations in the pipes.
●
Clean/change valve(s). Clear encrustations.
5.4 Fault:
The set pressure (p refer) is not reached in the test with compressed air or compressed air pump programs
(REMS Multi-Push SL/SLW).
Cause:
Remedy:
●
Installation or compressed air hose (Fig. 4 (23)) leaking.
●
Check installation for leaks. Change the compressed air hose.
●
No or too little pressure in the compressed air tank.
●
See 5.2 Fault:
●
REMS Multi-Push defective.
●
Have the REMS Multi-Push checked/repaired by an authorised REMS
customer service workshop.
5.5 Fault:
The set pressure (p refer) is not established in the test with water program (Multi-Push SLW).
Cause:
Remedy:
●
The water pressure of the house connection is greater than the set pressure
(p refer).
●
Close the shut-off valve of the house connection.
●
Suction/pressure hose (Fig. 1 (13)) or high-pressure hose (Fig. 4 (26)) leaking.
●
Change suction/pressure hose or high-pressure hose.
●
Hydro-pneumatic pump does not build up pressure.
●
Connect suction/pressure hose between the house connection and the
pressure test with water supply, see 2.6.2.
●
Stop tap of the water supply is closed or only partly open.
●
Fully open the stop tap.
●
No or too little air pressure in the compressed air tank.
●
Hydro-pneumatic pump requires compressed air, see 5.2 Fault:
●
REMS Multi-Push defective.
●
Have the REMS Multi-Push checked/repaired by an authorised REMS
customer service workshop.
5.6
Fault:
The pressure in the pipe to be tested is not relieved after running the test with water programs or during the test with water B, P+M
(REMS Multi-Push SLW).
Cause:
Remedy:
●
Pressure relief water drain (Fig. 4 (27)) is soiled or defective.
●
Clean the pressure relief water drain or have it replaced by qualifi ed personnel
or an authorised REMS customer service workshop.
●
REMS Multi-Push defective.
●
Have the REMS Multi-Push checked/repaired by an authorised REMS
customer service workshop.
5.7 Fault:
No or not enough ingredient is injected from the bottle.
Cause:
Remedy:
●
Unsuitable disinfectant, cleaning, preserving agent.
●
Use REMS Peroxi Color, REMS CleanH, REMS NoCor.
●
REMS V-Jet TW or REMS V-Jet H connected wrongly to the Multi-Push.
●
Note the direction of fl ow arrow, see also 2.5.
●
REMS V-Jet TW or REMS V-Jet H soiled.
●
Clean REMS V-Jet TW or REMS V-Jet H, see also 4.1.
●
REMS V-Jet TW or REMS V-Jet H defective.
● Wrong REMS V-Jet TW or REMS V-Jet H unit connected.
●
Have REMS V-Jet TW or REMS V-Jet H checked/repaired by authorised
REMS customer service workshop.
● Use REMS V-Jet TW exclusively for REMS Peroxi Color.
Use REMS V-Jet H exclusively for REMS CleanH cleaner and REMS NoCor
corrosion protection.
5.8 Fault:
The date and time must be reset every time the
REMS Multi-Push
is switched on.
Cause:
Remedy:
●
Battery depleted.
●
Change battery. See 4.1.
5.9 Fault:
The new version software was not installed.
Cause:
Remedy:
●
USB stick not recognised.
●
Use another USB stick.
●
New version software is not on the USB stick.
●
Copy new version software to the USB stick.
●
The USB stick was pulled out of the USB port
(Fig. 2 (33)) during the installation.
●
Repeat the procedure described in 2.3.. Use a USB stick with a LED if
possible.
●
A folder was created on the USB stick and the new version software was
copied into this folder.
●
Move the new version software into the main directory of the USB stick.
5.10 Fault:
The fl ushing and testing programs have been incorrectly displayed on the PC.
Cause:
Remedy:
●
The font “Lucida Console” is required for a correct display.
●
Select font “Lucida Console”, install if necessary.
5.11 Fault:
Printing on paper weak or illegible. Printout aborted prematurely.
Cause:
Remedy:
●
Weak battery charge.
●
Charge battery.
●
Paper reel inserted incorrectly in printer.
●
Insert paper roll, see
3.8.
●
The printer can only be used as of Version Software 2.0.
●
Load software by USB stick as a download under www.rems.de → Downloads
→ Software into the controller of the REMS Multi-Push, see 2.3.
5.12 Fault:
“Error” is displayed on the screen (6).
Cause:
Remedy:
●
A fault has occurred.
●
Unplug REMS Multi-Push. Remove all hoses, caps and stoppers. Then restart
REMS Multi-Push. If “Error” still appears, have the REMS Multi-Push checked/
repaired by an authorised REMS customer service workshop.
29