Do not touch any objects or the ground with the running saw.
Keep your hands away from the sawing area.
Do not reach underneath the
workpiece. Contact with the saw blade can cause injury
Keep highly infl ammable materials away from hot sawing chips during
There is a danger of fi re!
Make sure that the tiltable support shoe (6) is always in contact with the
The saw blade can jam and lead to loss of control
When you have fi nished the work, switch off the power tool and do not
remove the saw blade from the cut until it has come to a standstill.
avoids recoil and allows you to put down the power tool safely.
Only use undamaged, fl awless saw blades.
Bent or blunt saw blades can
Do not slow down the saw blade after switching off by pressing against
The saw blade could be damaged, break or cause recoil.
Wait until the power tool has come to a standstill before you put it down.
The inserted tool can jam and lead to loss of control over the power tool.
Pull out the mains plug or remove the battery before attaching/detaching
There is a danger of injury.
Pull out the mains plug or remove the battery before adjusting the support
There is a danger of injury.
Do not use the power tool if it is damaged.
There is a danger of accident.
Never let the power tool operate unattended. Switch off the power tool
during longer work breaks, pull out the mains plug/battery.
can cause hazards which lead to material damage or injury when left unattended.
Children and persons who, due to their physical, sensory or mental abilities
or lack of experience and knowledge are unable to operate the power tool
safely may not use this power tool without supervision or instruction by a
Otherwise there is a risk of operating errors and injuries.
Only allow trained persons to use the power tool.
the power tool when they are over 16, when this is necessary for their training
and when they are supervised by a trained operative.
Check the power cable of the electric al device and extension leads regularly
Have these renewed by qualifi ed experts or an authorised REMS
customer service workshop in case of damage.
Only use approved and appropriately marked extension leads with a suffi -
cient cable cross-section.
Use extension leads up to a length of 10 m with
cable cross-section 1.5 mm
, from 10 – 30 m with cable cross-section 2.5 mm
Safety instructions for batteries
WARNING
Read all safety warnings, instructions, illustrations and specifi cations provided
Failure to follow all instructions listed below may result in
electric shock, fi re and/or serious injury.
Save all warnings and instructions for future reference.
See also www.rems.de → Downloads → Instruction Manuals.
WARNING
Danger with a medium degree of risk which could result in
death or severe injury (irreversible) if not heeded.
Danger with a low degree of risk which could result in minor
injury (reversible) if not heeded.
NOTICE
Material damage, no safety note! No danger of injury.
Read the operating manual before starting
Electrical device complies with protection class II
Not suitable for using outdoors
Environmentally friendly disposal
Use for the intended purpose
WARNING
REMS reciprocating saws are intended, using suitable saw blades, for sawing
different materials, e.g. steel pipes, stainless steel pipes, cast iron pipes, other metal
profi les, wood, wood with nails, pallets, building materials, plastics, also for plunge-
cut sawing in material that is not too hard.
All other uses are not for the intended purpose and are prohibited.
REMS Tiger VE/SR/pneumatic: Drive machine, Allen key, guide holder up to
2", 2 REMS special saw blades up to 2"/140-3.2, sheet steel box, operating
REMS Puma VE: Drive machine, Allen key, 1 REMS saw blade 210-1.8/2.5,
sheet steel box, operating instructions
REMS Cat VE: Drive machine, Allen key, 1 REMS universal saw blade 150-1.8/2.5,
sheet steel box, operating instructions
S C
at 22 V VE: Drive machine, battery, rapid charger, Allen key, 1 REMS
universal saw blade 150-1.8/2.5, sheet steel box, operating instructions
S T
iger 22 V VE: Drive unit, battery, rapid charger, Allen key, guide holder
2“, 2 REMS special saw blades 2“/140-3.2, steel case, instruction manual.
REMS Tiger drive unit 560000
REMS Tiger VE drive unit 560008
REMS Tiger SR drive unit 560001
REMS Tiger pneumatic drive unit 560002
S T
iger 22 V VE drive unit Li-Ion 560011
REMS Puma VE drive unit 560003
REMS Cat VE drive unit 560004
S C
at 22 V VE drive unit Li-Ion 560010
Battery Li-Ion 21.6 V, 5.0 Ah 571581
Battery Li-Ion 21.6 V, 9.0 Ah 571583
Rapid-charger Li-Ion 230 V, 90 W 571585
Guide holder ⅛" – 2" 563000
Guide holder 2½" – 4" 563100
Guide holder 5" – 6" 563200
Protective cap for guide holder, for clamping thin-walled material 563008
Steel case (REMS drive units) 566051
Steel case (REMS drive units Li-Ion) 566030
Right-angled sawing with REMS Tiger VE/SR/pneumatic:
With guide holder 563000 and
REMS special saw blade 561001, 561007
Pipes (also plastic jacketed) ⅛" – 2"
With guide holder 563100 and
REMS special saw blade 561002
Pipes (also plastic jacketed) 2½" – 4"
With guide holder 563200 and
REMS special saw blade 561008
Pipes (also plastic jacketed) 5" – 6"
REMS Tiger SR with guide holder
and REMS universal saw blade 561005, 561003
Stainless steel pipes ⅛" – 2" or 2½" – 4"
6
To Next Page
Loading...
General