resideo Braukmann KS30E-30

Questions and Answers

J
Jessica WheelerAug 2, 2025
What to do if water level in brine cabinet of resideo Water Dispenser reaches overflow?
- A
  annataylorAug 2, 2025
  If the water level in the brine cabinet of your resideo Water Dispenser reaches overflow, it could be due to several reasons. First, ensure the line pressure is within the specified range (1.7 - 5.0 bar for the UK / 1.0 - 8.0 bar for EU) by connecting a pressure gauge to a water outlet. If the pressure falls outside this range, you may need to fit a pressure reducing valve or booster pump. Also, check that the drain line isn't kinked, blocked, or frozen, and verify that the power is on and connections are secure, especially after a power interruption.
O
Omar VargasAug 5, 2025
How to fix if resideo Braukmann KS30E-30 still dispensing hard water?
- B
  Brian RobbinsAug 5, 2025
  If your resideo Water Dispenser continues to produce hard water, there are several things to check. First, make sure there is at least 150 mm of salt in the brine cabinet; if not, fill it with salt. Ensure the power is on and all connections are secure. Also, confirm that the softener is online by closing the by-pass valve, opening the inlet and outlet valves, and manually restarting the regeneration. Lastly, verify that the hardness setting is correct and reset it if necessary.
D
danielmcdanielAug 10, 2025
What to do if resideo Braukmann KS30E-30 displays error code Err 1?
- R
  rachel62Aug 10, 2025
  If the electronic display of your resideo Water Dispenser is showing an error code "Err 1" and an audible alarm is sounding, check that all the connections are secure. Then, turn the power off for 10 seconds and turn it back on to allow the system to reset. If the digital display is blank, verify that the power is turned on and all the connections are secure.
P
pateljosephAug 14, 2025
How to fix no water from resideo Water Dispenser?
- S
  Stephen WrightAug 15, 2025
  If your resideo Water Dispenser isn't dispensing any water, start by checking if the mains stop valve is open and open it if it is closed. Then, check the inlet and outlet valves of the water softener and open them if they are closed.
N
noah41Aug 19, 2025
Why is water constantly running from drain of resideo Braukmann KS30E-30 Water Dispenser?
- J
  James AdamsAug 19, 2025
  If water is constantly running from the drain of your resideo Water Dispenser, first determine if the unit is in recharge mode. If it is, this is normal, and you should wait until the recharge is complete. If it is not in recharge mode, ensure that the power is on, as there should be no flow to drain in the service position.
J
John ContrerasAug 23, 2025
How to reduce excessive salt usage in resideo Braukmann KS30E-30?
- M
  Michael HallAug 23, 2025
  If your resideo Water Dispenser is using an excessive amount of salt, check the hardness setting and reduce it if it is incorrect.
J
Jason HaasAug 27, 2025
How to fix resideo Water Dispenser regenerating at wrong time?
- M
  Monique PerezAug 27, 2025
  If your resideo Water Dispenser regenerates at the wrong time, reset the present time to the correct time.

Summary

Introduction to Resideo Braukmann Water Softener

General Comments and Standards

Read and understand operating instructions before use, observe local standards and technical specifications.

Safety Guidelines

Follow installation instructions, use appliance as intended, ensure condition, and use only authorized personnel.

Intended Use of Water Softener

Designed for softening domestic water; any other use is forbidden and at user's responsibility.

Technical Data for Softener Models

Provides specifications for softener models, connections, pressure, temperature, flow rates, and resin quantity.

Quick Operation Guide

Display and Control Elements Overview

Explains the softener's display indicators and the function of each control button for operation.

Standard Initial Settings

Details the initial setup process, including display flashing and valve rotation to service position.

Programming the Time of Day

Step-by-step instructions for setting the current time of day on the water softener's control panel.

Installation Guidelines

Setup Requirements and Regulations

Adherence to national guidelines, water quality standards, frost protection, ambient temperature, and general safety.

Installation Layout Diagram

Diagram illustrating the physical placement and connection points for the water softener installation.

Technical Overview of Device Components

Identifies and labels the various components and connection ports of the water softener unit.

Softener Installation Steps

Covers positioning, inlet/outlet connections, drain and overflow setup, and electrical connections for installation.

Description of Functionality

Functions and Features Explained

Details the unit's intelligent regeneration, capacity management, disinfection, and salt type requirements.

Daily Operation Procedures

Covers charge bar, display reset, power loss handling, flow indication, and manual regeneration.

Setting Blended Water Hardness

Instructions for testing and adjusting the water hardness using the blending valve after initial setup.

Maintenance and Care

Regular Maintenance Work Checks

Operator tasks include checking salt, water hardness, and for leaks to ensure proper functioning.

Operator Responsibilities

Operator's role in maintaining optimal functionality, checking water quality, pressure, and system integrity.

Maintenance and Wearing Parts Replacement

Information on replacing worn components and the recommended annual servicing for the water softener.

Disposal and Environmental Information

Procedures for safe disposal and recycling of the water softener and its electrical parts at end-of-life.

Troubleshooting Common Issues

Problem Checklist and Solutions

Lists common issues like hard water, overflow, or no water, with corresponding steps to resolve them.