To Next PageTo Next Page
Need help?Do you have a question about the Response Alarms RE5000S and is the answer not in the manual?
General| Brand | Response Alarms |
|---|---|
| Model | RE5000S |
| Category | Security System |
| Language | English |
Provides crucial safety advice and precautions to be followed before commencing installation.
Discusses system operation, access codes, and recommendations for physical security.
Lists the necessary tools and equipment for installing the alarm system.
Details optional accessories available to enhance the alarm system's capabilities and protection.
Explains how to arm specific zones while leaving others inactive for partial security.
Guidance on assessing security needs and planning the system's layout and zoning.
Describes the function of LEDs, buttons, and the keypad on the control unit.
Provides recommendations for selecting an optimal and secure placement for the control unit.
Step-by-step instructions for mounting, wiring, and connecting the control unit.
Explains the purpose, installation, and function of the control unit's backup battery.
Guides on programming the system's unique identification code for communication.
Instructions for activating and using the system's test mode for setup verification.
Procedure for setting the detector's house code and zone assignment.
Detailed steps for physically installing the PIR detector, including corner mounting.
How to verify the detector's operation and radio range during installation.
Guidance on selecting an optimal, visible, and secure mounting position for the siren.
Steps for physically mounting the solar siren and strobe unit to an external wall.
Configuration options including Siren Code and Alarm Duration dip switch settings.
Setting the system's unique identification code for detector and remote communication.
Configuring zones for immediate alarm activation or a timed entry delay.
Setting the duration before the system fully arms after the exit period.
Defining the maximum duration the alarm siren will sound after activation.
Establishing the primary four-digit code for system operation and programming.
Enabling chime alerts for specific zones, typically magnetic contact detectors on doors.
Setting the time allowed to disarm the system upon triggering an entry delay zone.
Selecting which zones are active or omitted when the system is set to 'Part Arm'.
Choosing audible feedback (tone or silent) during the exit delay period.
Enabling fast arming and part-arming without needing to enter an access code.
Configuring the system to detect and alert on radio jamming attempts.
Programming codes to link the control unit with external sirens and medical alert pendants.
Setting a secondary four-digit code for limited system access (arming/disarming only).
Procedure for arming the system completely when leaving the premises.
How to arm the system while remaining on the premises, allowing access to omitted zones.
Steps to deactivate the alarm upon entering through an entry delay zone.
Procedure to cancel an active alarm and reset the system after an event.
Instructions for initiating emergency alerts for personal attack, medical, or fire events.
How the system monitors and indicates low battery conditions in detectors and peripherals.
Guidelines for regularly testing the alarm system's functionality and components.
Cleaning and care instructions for the main control unit, avoiding solvents.
Maintenance procedures for the external siren, including solar panel cleaning.
Information on the lifespan, charging, and responsible disposal of rechargeable batteries.
Guidance on replacing batteries in detectors and remote control units.
Troubleshooting steps for when the system fails to arm, indicated by three bleeps.
Diagnosing issues when a zone is triggered but no alarm sounds, e.g., entry delay.
Resolving low battery indications for detectors and the control unit itself.
Investigating and resolving false alarms or unintended full alarm activations.
Troubleshooting steps for power-related issues where the control unit is unresponsive.
Addressing situations where sirens sound without an apparent trigger or system fault.
Solutions for problems with the control unit keypad not recognizing entered access codes.
Diagnosing chime activation for detectors, potentially related to Door-Chime settings.
Troubleshooting communication failures between detectors and the control unit.
Addressing issues where the external siren activates but the control unit does not register an alarm.
Fixing problems where the external siren and strobe fail to activate during an alarm event.
Troubleshooting communication failures with the passive infra red motion detectors.
Diagnosing PIR sensor issues, including sensitivity and mounting height.
Identifying potential issues with PIR detectors, such as low battery or environmental factors.
Steps to prevent unwanted triggers from PIR detectors due to heat or movement.
Troubleshooting common problems with the wireless remote control unit.
Fixing issues related to the remote control's indicator light not illuminating.
Troubleshooting failures with magnetic contact detectors on doors or windows.
Addressing issues with the indicator light on magnetic contact detectors.
Steps to prevent false triggers from magnetic contact detectors.
Information on adding a second siren for enhanced security coverage.
Using a non-functional unit as a visual deterrent to deter potential intruders.
A magnetic detector offering optional hard-wired input capabilities.
A lightweight device for transmitting a medical alert signal to the control unit.
A smoke detector that signals fire events to the alarm system, providing high safety.
A device connecting to the telephone line to automatically call for help during alarms.
Details the product warranty terms, conditions, and exclusions.
Technical specifications for the main alarm control unit, including zones and features.
Technical specifications for the PIR motion sensor, including detection range and battery.
Specifications for the door/window contact sensor, including wired input options.
Technical details for the external siren and strobe unit, including power and sound output.
Specifications for the wireless remote control unit, including buttons and battery.
Specifications for the standard magnetic contact detector, including operating gap.
Technical specifications for the medical alert pendant, including transmission and options.
Specifications for the optional security dialler, including phone storage and trigger inputs.
Technical details for the wireless smoke detector, including its siren and communication.
