REVELL ’62 Chevy Impala Hardtop User Manual

DECAL PLACEMENT
10
Gloss Gold Metallic
Semi Gloss Black
Cream
Red
Gloss White
Chevy Engine Red
Aluminum
Silver
Steel
Turn Signal Amber
This paint guide is provided to complete this kit
as shown on the box.
Ce guide de peintures est fourni pour reproduire le modèle
réduit qui apparaît sur la boîte.
Or brillant metalisé
Noir satiné
Créme
Rouge
Blanc mat
Rouge moteur Chevy
Aluminium
Argent
Acier
Ambre
* Study the assembly drawings.
* Each plastic part is identified by a number.
* In the assembly drawings, some parts will be
marked by a star (★) to indicate chrome
plated plastic.
* For better paint and decal adhesion, wash
the plastic parts in a mild detergent solution.
Rinse and let air dry.
* Check the fit of each piece before
cementing in place.
* Use only cement for polystyrene plastic.
* Scrape plating and paint from areas
to be cemented.
* Allow paint to dry thoroughly before
handling parts.
* Any unused parts may be discarded.
DECAL APPLICATION INSTRUCTIONS
1. Cut desired decal from sheet.
2. Dip decal in water for a few seconds.
3. Place wet decal on paper towel.
4. Wait until decal is movable on paper backing.
5. Place decal in position on model, face up and
slide backing away.
6. Press out air bubbles with a soft damp cloth.
7. Milkiness that may appear is for better decal
adhesion and will dry clear. Wipe away any
excess adhesive.
8. Do not touch decal until fully dry.
9. Allow the decals 48 hours to dry before
applying clear coat.
NOTE: Decals are compatible with
setting solutions or solvents.
READ THIS BEFORE YOU BEGIN LIRE CE QUI SUIT AVANT DE COMMENCER
* Etudier les schémas de montage.
* Chaque pièce en plastique est identifiée par un numéro.
* Sur les schémas de montage, certaines pièces sont
marquées d'une étoile (★) pour indiquer qu'elles sont en
plastique chromé.
* Pour une meilleure prise de la peinture et des autocollants,
laver les pièces en plastique avec une solution détergente peu
concentrée. Les rincer et les laisser sécher à l'air.
* Vérifier que chaque pièce s'ajuste bien avant
de la coller en place.
* N'utiliser que de la colle pour polystyrène.
* Gratter les parties à coller pour enlever le chrome et la peinture.
* Laisser la peinture bien sécher avant de manipuler les pièces.
* Toute pièce inutilisée peut être jetée.
DIRECTIVES D'APPLICATION DES AUTOCOLLANTS
1. Découper l'autocollant désiré de la feuille.
2. Tremper l'autocollant dans de l'eau pendant quelques secondes.
3. Placer l'autocollant mouillé sur une serviette en papier.
4. Attendez que l'autocollant puisse être déplacé sur son
support en papier.
5. Mettre l'autocollant en position sur le modèle face sur
le dessus et faire glisser le support pour l'enlever.
6. Appuyer avec un chiffon doux humide pour éliminer les bulles d'air.
7. La substance laiteuse qui peut apparaître est destinée à
améliorer l'adhésion de l'autocollant et devient incolore au
séchage. Essuyer pour enlever tout excédent d'adhésif.
8. Ne pas toucher l'autocollant tant qu'il n'est pas bien sec.
9. Laisser l'autocollant sécher pendant 48 heures avant
d'appliquer une couche transparente.
REMARQUE: Les autocollants sont compatibles avec
les solutions de fixage ou les solvants.
'62 CHEVY
®
IMPALA
™
HARDTOP
KIT 4246 85424600200
If you have any questions or comments, call our hotline at: (800) 833-3570
or, please write to:
Revell Inc Consumer Service Department, 1850 Howard Street Unit A, Elk Grove Village, Illinois 60007
Be sure to include the plan number (85424600200), part number, description, your return address and phone number.
Visit our website: www.revell.com
Revell Inc Elk Grove Village, IL. Copyright © 2010. All rights reserved.
Kit 4246 - Page 12
Style was paramount when the
1962 Chevrolet
®
Impala
™
made its
debut. The '62 Impala
™
Hardtop
had new "C" pillar body styling
and featured the convertible roof
styling which was shared with
other General Motors
®
full size
hardtop coupes. This new styl-
ing proved to be extremely pop-
ular and contributed to the col-
lectability of the 1962 Impala.
Your Revell kit features a detailed
409 cu. in. V-8 engine with duel
carbs, optional drag headers,
exhaust, roll bar, raised rear suspen-
tion, drag slicks and authentic facto-
ry stock and custom drag graphics.
* REPEAT SEVERAL TIMES
* A REPETER PLUSIEURS FOIS
* CEMENT TOGETHER
* A COLLER
* REMOVE AND THROW AWAY
* A RETIRER ET JETER
* DO NOT CEMENT
* NE PAS COLLER
* DECAL
* DECAL COMANIE
* ASSEMBLY CAUTION
*ATTENTION D ASSEMBLEE
* OPTIONAL PARTS
* PIECES EN OPTION
* REPEAT PROCEDURE
* R E P E T E Z L E P R O C E D E
``` ` ``

REVELL ’62 Chevy Impala Hardtop Specifications

General

Brand	REVELL
Model	’62 Chevy Impala Hardtop
Category	Motorized Toy Car
Language	English

Summary

General Information and Preparation

Assembly Preparation Guidelines

Read assembly drawings, wash parts, check fit, use correct cement, scrape plating, allow paint to dry.

Decal Application Process

Detailed steps for cutting, wetting, positioning, and drying decals for optimal adhesion.

Engine Assembly

Standard Engine Components

Details on engine halves, cylinder heads, intake manifold, carburetors, and other standard engine parts.

Drag Version Engine Options

Optional drag headers and air cleaner for the drag version of the engine assembly.

Engine to Chassis Integration

Connecting the engine and its components to the chassis and front suspension.

Exhaust and Suspension Assembly

Exhaust System Components

Assembly of the exhaust pipes, mufflers, and hangers for both standard and drag versions.

Suspension System Components

Assembly of front and rear suspension parts, including springs and coil-overs.

Drivetrain and Rear Suspension Details

Installation of driveshaft, differential, rear axle, control arms, and shocks.

Interior Assembly

Interior Seating and Floor

Assembly of front and rear seats, interior floor, and side panels.

Dashboard and Controls

Assembly of the dashboard, gauge panel, steering column, steering wheel, and firewall.

Drag Version Interior Omissions

Instructions for omitting the rear seat for the drag version assembly.

Radiator and Hose Assembly

Radiator and Fan Shroud

Assembly of the radiator, fan shroud rings, and fan shroud.

Radiator Hose Installation

Installation of the upper and lower radiator hoses.

Wheel Assembly

Standard Wheel Assembly

Assembly of standard wheels, including inner and outer wheel parts.

Drag Version Wheel Assembly

Assembly of drag version wheels and tires, including front and rear slicks.

Window and Front Bumper Assembly

Window Components

Installation of windshield, rear window, and vent windows.

Front Bumper and Grille

Assembly of the front bumper, grille, headlights, and filler panel.

Hood and Rear Bumper Assembly

Hood Assembly

Installation of the hood, hood emblems, and hood hinges.

Rear Bumper Assembly

Installation of the rear bumper, taillights, trunk emblem, and license plate.

Decal Placement - Stock

Stock Decal Placement Diagrams

Visual guide for applying decals to the stock version of the model.

Decal Placement - Drag

Drag Version Decal Placement

Visual guide for applying decals to the drag version of the model.