2.1 CONSTRUCTION AND PRINCIPLE OF OPERATION
Casing: made of steel, additionally covered with insulating material
2. DEVICE CHARACTERISTICS
which improves acoustic and thermal properties of the unit. It has handles
and have diameters enables of installation of the most popular sizes of ventilation
ducts. The housing has an inspection door that allows for easy access to filters
Filters: the unit has two sets of filters - prefilter G3 and filter F9, which properly
maintained (see point 5) guarantee appropriate purity of the air supplied
there is no need for using additional humidifier.
for easy assembly of the device. The connectors are made of plastic
to the rooms.
Differential pressure switch: measuring and comparing the pressure after
the differential pressure switch with the connectors in the inspection door
using transparent pipes in the way shown on picture below.
and before the F9 filter informs about the need of replacement the filter,
triggering filter alarm. Before mounting the energy recovery unit, connect
Enthalpy heat exchanger: made of the special material enabling efficient
recovery of heat and moisture from room exhaust air (enthalpy efficiency above
7 0 % ! ) . T h a n k s t o t h e r e c o v e r y o f m o i s t u r e i n m a n y c a s e s
and exchanger.
(i. e. the pressure difference behind and before the filter at which the device
and use a flat screwdriver to change this pressure. The value recommended
Supply and exhaust fan: energy-efficient DC fans which ensure airflow through
2.2 DEVICE DIMENSIONS
the exchanger and ventilation ducts. They have 10 predefined rotational speeds,
enabling to adjust the device performance for the current needs. Detailed
performance characteristics of the whole units can be found in section 2.4.
will trigger the filter alarm). To do this, unscrew the upper plastic housing
There is a possibility to change the differential pressure switch setpoint
INSPIRO 150
by the supplier is 20 Pa.
3.1 GENERAL PRINCIPLES
4. INSTALLATION INSTRUCTIONS
1.4 USE
2.1 CONSTRUCTION AND PRINCIPLE OF OPERATION
6.1 CHARACTERISTIC
1.INTRODUCTION
1.1 PRECAUTIONS
1.2 TRANSPORT
1.3 PACKAGE CONTENT
2. DEVICE CHARACTERISTIC
2.2 DEVICE DIMENSIONS
2.3 DEVICE TECHNICAL DATA
2.4 WORKING CHARACTERISTICS
3. ASSEMBLY
3.2 DUCTING
4.1 CONNECTION OF THE DEVICE TO THE ELECTRICAL SYSTEM
5. PRECAUTIONS & WARNINGS
6.CONTROLS
6.2 COMMISSIONING
6.3 CONTROLLER'S PARAMETER
6.5 INTELLIGENT CONTROL PANEL PREMIUM
6.4 INTELLIGENT CONTROL PANEL STANDARD
7. CONNECTION SCHEME
8. TERMS OF WARRANTY
6.6 DIAL SWITCH
1.2 TRANSPORT
- instruction and warranty card
Energy revocery units Reventon Group INSPIRO series are designed
1.1 PRECAUTIONS
1.4 USE
They are designed for ventilation of residential buildings as well as halls,
warehouses, shops, services or workshops. Energy recovery allows
and safety. In case of any doubts please contact directly Reventon Group sp. z o. o.
[Ltd.]. The supplier reserves the rights to make changes to the technical
documentation without previous notice. Reventon Group sp. z o. o. [Ltd.]
During the acceptance of goods, it is needed to check the device to exclude
- energy recovery unit
for a significant reduction of the building's operating costs.
- silicon hose of differential pressure switch
in the damage report in presence of the supplier.
- intelligent controller STANDARD or PRESTIGE (option)
Thank you very much for purchasing energy recovery unit INSPIRO. We would
like to congratulate you on excellent choice. Please read and keep this manual.
any damages. During the transport, it is needed to use the proper equipment,
(heat and moisture). These devices enables ventliation of the building.
1. INTRODUCTION
for ventilation systems as an important element enabling energy recovery
is not responsible for the damages which occur due to improper installation,
not keeping the device in repair or using the device out of line. The installation
should be carried out by the professional installers, who possessthe
qualifications to install these types of devices. The installers are responsiblefor
making the installation as instructed in the technical data. In case
it is necessary to carry the device by two people. In case of any damages please fill
of unserviceable please plug out the device and contact with the authorizedfor
repair person or the supplier. During the installation, use, service and periodical
inspections all regulations and safety rules must be followed.
The buyer and the user of the device Reventon Group brand should read carefully
the following instructions and proceed to the content recommendations.
Proceeding due to the following instruction guarantees the correct usage
1.3 PACKAGE CONTENT
ENG
DOKUMENTACJA TECHNICZNA
To Next Page
Loading...