Revox Exception E426

t6t
I
r7l
ll>
6. OPERATING
THE E 426
CD
PLAYER
Front
panel
of
the E
426
CD
player
[3]
Power Turns the CD
player
on or switches
it
to
standby
mode.
14,51
<
,
> Plays the current or the next track
from
the
beginning. Pressing the
<
key
twice
within one second takes
you
to the
begin-
ning of the
previous
track.
For aud i ble
fast-forward/fast- reverse,
press
and
hold the
<
or > key.
The function starts with steps
of
I
second
and
accelerates
later
to
steps of 5 seconds.
stop,
Stops
play,
shows
total
playing time.
play, pause
Plays CD or suspends
play.
[27]
UNBALANCED OUT
Single-ended analogue audio outputs,
left
and
right
(RCA).
T28,291OUTPUT
DIGITAL
All
information
that
is
stored
on the CD
is
fed to the two digital outputs
(RCA,
BNC).
The outputs are electrically
insulated from
the circuitry by
means
of a
transformer.
I24lAC
POWER
AC
power
connection
power
switch
mains fuse
Programming
functions
The CD
player
allows
you
to compile
a
playlist
compris-
ing up to
20
tracks of the same
CD.
For
programming, use the controls on the
unit or the RC
28
remote control.
Enabling the
repeat function
a
a
Press and
hold
the mode key
[8]
for about 5 sec-
onds,
<REP
ONE, is shown on the display.
Select the
<REP DISC> or <SHUFFLE> function or the
program-
ming function by
pressing
the mode key
IBJ.
<REP ONE>
plays
the current track repeatedly,
<REP
DISC>
plays
the whole disc repeatedly, and
<SHUF-
FLE>
plays
the
tracks
in random order.
Press the
lltr
key
[7]
to enable the selected
function.
Press
the
I
key
t6J
twice to
return
to
normal opera-
tion
mode
of the CD
player.
Enabling the
programming
function
.
Press and hold the mode key
[8i
for about 5 sec-
onds,
<REP
ONE> is shown on the display.
.
Press and hold
the
mode
key
t8J
until
the track
number is replaced by
two
lines
and
<PROG>
flashes.
Now,
you
can
enter the
first programme step.
Entering a
programme
step
Press the keys marked <,>
14,51
to
select the de-
sired track
(e.9.
04)
for
step
1.
The display
shows the selected track
number
(04),
the number
of
programme
steps
(first
two
digits),
and the total playing
time of the
programme
(min./
sec.): e.g.
<01
03:54>. Simultaneously,
<PROGn
flashes.
Press the mode
key
[8]
to store the
programme
step,
again
the track number is replaced
by
two lines.
Press the keys marked <
,
>
14,51
to select the
next
track.
Press the mode
key
[8J
to store
the
programme
step.
Follow this
procedure
to
enter up to 20
programme
steps.
The maximum programme
playing
time is 99
min-
utes.
[8]
mode
Press momentarily:
Cycles
through the
four time display
modes:
remaining
time of
the current
track,
elapsed
time of the
whole CD, remaining
time of the
whole
CD, and
elapsed
time of
the current track.
The time modes
of the
CD are shown
by
a corresponding
symbol
on the
display.
Press and hold for about 5 seconds:
Switches
to
the
programming functions.
[10]
Open/Close
Opens
CD compartment or closes
CD com-
partment
and
plays
CD.
t9l
display Shows track
number
and
various time
in-
dications. See
programming
functions.
Operating the
E 426
CD
player
with
the
lR remote con-
trol
[1]
off
t3l
cD
[7]
<<
,
>>
Switches the CD player off.
Switches
the
entire
Exception hi-fi system
off
if the components
are
interconnected.
Switches the CD
player
on and
plays
the
first track of the CD.
lf ihe CD
player
is interconnected
with the
E 450 amplifier via Revox Link, the ampli-
fier automatically
switches on
and to CD
if
in
standby
mode
or to CD
if
already
in
operation.
Aud
i
ble
I
asl-f orw ar d /fast-
reverse.
[8]<,>
Track
selection.
Rear
panel
of the E
426
CD
player
[25]
Revox Link
Connectors
for interconnected operation
with
the
E 450
amplifier.
[26]
BALANCED OUT
Balanced analogue audio outputs,
left
and
right
(XLR).