- 1 -
Important Information for Equipment Safety
- Read Before Use -
1
SLG-150V Series
LED FIBER OPTIC ILLUMINATOR
Instruction Guide
Thank you for purchasing a SLG-150V. To ensure proper use of the
product, please read this Instruction Guide before use and keep it
for your future reference.
SLG-150V is intended to be used as light sources for image
processing and industrial inspections. SLG-150V is used with
light guides attached. This enables the selection of a lighting
pattern that is suitable for the application.
*
A ferrule is not provided with this product. Order one separately.
The light intensity can be controlled in up to 1024 steps.
Status conrmation and operation settings can be performed on the LCD.
In addition to the manual control from the front panel, external
control with parallel communications (including digital intensity
control and analog intensity control), Ethernet communications,
and RS-232C communications is also possible.
A feedback function is available to suppress fluctuations in the
illumination.
Features
* If the above mark appear on the product, refer to this document and conrm any hazards.
Light Emitted by the Product
This product emits high-intensity visible light. Because light-absorbing materials convert incident light into heat, heat-sensitive or
ammable light-absorbing materials may be damaged. Always observe the following precautions when you use the product. Incorrect
usage of the product may jeopardize safety.
• Never look directly into the opening of the ferrule or the
light guide exit while light is being emitted. There is a risk of
damage to your cornea and retina.
• Never cover the ferrule or light guide exit with your hand or
any other part of your body. There is a risk of burn injury.
• Never cover the
ferrule
or light guide exit. Doing so may result in re.
• When you illuminate a heat-sensitive, light-absorbing, or ammable
material, provide an appropriate distance between the light guide
and material and use a suitable light intensity. There is a risk of
damage to the material or re.
W A R N I N G
RISK GROUP 3
Possibly hazardous optical radiation
emitted from this product.
Do not stare at operating lamp.
Eye injury may result.
WARNING
WARNING LABEL
RISK GROUP 1 / 2 / 3
Possibly hazardous optical radiation emitted from this product.
Do not stare at operating lamp.
Eye injury may result.
This product has been designed with full consideration of safety. Incorrect usage of the product may result in re, electric shock, or other serious accidents.
Observe the following precautions.
Do not disassemble or modify the
product. Doing so may result in re
or electric shock.
Do not touch the AC power cord
during lightning. This may result in
electric shock.
Make sure that the product is free
of moisture or any liquid. Exposure
to water or other liquid may result in
re or electric shock.
Do not touch the plugs or switches
with wet hands. Doing so may result
in electric shock.
If an abnormal condition, such
as smoking, abnormal heating,
abnormal odor, or noise, occurs,
stop using the product immediately,
turn OFF the power switch, and
unplug the AC power cord from the
wall socket. Continued use may
result in re or electric shock.
Before connecting or disconnecting
cables, make sure that the power
switch is turned OFF. Failure to do
so may results in re, electric shock
or breakdown in the Light Source
Unit.
Make sure to use the attached AC power cord or an equivalent such as KWD-JP-
2MBSY of Kawasaki Electric Wire Co. Ltd. when the equipment is used in Japan.
Please use designated power
sources with stable voltage. Sharing
a power source with inverters,
motors, etc. may cause malfunction.
Plug the AC power cord directly into
the wall socket. Using a power strip
or connecting many loads from one
electrical socket may cause fire or
electric shock.
M
ake sure that the light guide to be
connected matches the product's
specications and dimensions.
Using a light guide that does not
match the product's specifications
and dimensions may result in
product failure.
Do not bundle product cables with
high-voltage lines or power lines.
Doing so may cause the product to
malfunction. Allow leeway between
the cables when installing them.
Do not drop or subject the product
to impact. Doing so may result in
product failure.
Always ground the power cord with
an earth pin of the plug. Not doing so
may cause product failure or electric
shock due to static electricity, which
may destroy electrical components,
including those in the Light Source
Unit.
Always place the product on a
stable and at surface. Not doing so
may result in the product falling or
toppling,
which may cause bodily injury or
product malfunction.
Do not disconnect cables or
disassemble product while
operating. Doing so may result in
product failure.
Do not place product in direct
sunlight or in a very humid
environment.
Doing so may result in fire due to
internal temperature rise.
Always hold onto the plug or
connector when disconnecting the
cables. Pulling on the cable may
damage the cable and result in re
or electric shock.
Do not bend a cable past its natural
bending radius or jam a cable
into a narrow space when wiring
the product. Doing so may cause
product failure.
Before moving the product,
disconnect all connecting cables.
Damaging the cables may result in
re or electric shock.
Do not wipe the product with organic
solvents, such as paint thinner
or benzene. Discoloration or
deterioration of the product surfaces
may occur.
If there is dust or other foreign
matter on the electrodes, turn OFF
the power switch and then use a dry
cloth to remove the dust or foreign
matter.
Failure to do so may result in re.
Items with this mark indicate
that incorrect usage may result
in serious injury or death.
Items with this mark indicate that
incorrect usage may result in
injury or property damage.
Hazards caused by incorrect usage and their levels are classied with the following indication:
Warning
Items and its details to be observed are classied into the following indication:
Unplug AC
The above marks show the items
prohibited.
The above marks show the instruction
which must be observed.
Unplug AC
RISK GROUP 2
Possibly hazardous optical radiation
emitted from this product.
Do not stare at operating lamp.
Eye injury may result.
CAUTION
RISK GROUP 1
NOTICE
Possibly hazardous optical
radiation emitted from this product.
Do not stare at operating lamp.
To Next Page
Need help?
General
