Rexel 250 S3 User Manual

DESKSIDE AND OFFICE
230V MACHINES
ILLUSTRATED PARTS LISTS
AND
SERVICE INSTRUCTIONS
Compiled by David Bird Issue No 7
Approved by Paul Aries (Technical Manager) Date
REXEL BUSINESS MACHINES, DROITWICH, WORCESTERSHIRE, WR9 9AP, ENGLAND
TELEPHONE +44 (0) 1905 771555 FAX +44 (0) 1905 823374

Rexel 250 S3 Specifications

General

Brand	Rexel
Model	250 S3
Category	Paper Shredder
Language	English

Summary

DESKSIDE AND OFFICE 230V MACHINES

PREFACE

Illustrated Parts Lists

Details of replacement part numbers with supporting diagrams.

Service Instructions

Recommended servicing procedures with pictorial diagrams.

Safety Warnings

Critical safety precautions for electrical mains supply.

OPERATIONAL TEST PROCEDURES

Section 1: Top Cover Maintenance

Top Cover Removal

Steps for removing the top cover for visual inspection.

Top Cover Replacement

Instructions for refitting the top cover after maintenance.

Section 2: Cutting Head Maintenance

Cutting Head Removal and Replacement

Procedures for removing and refitting the cutting head assembly.

Section 3: Printed Circuit Board (PCB) Maintenance

PCB Removal and Replacement

Steps to remove and refit the PCB from the top cover.

Section 4: Auto Start Sensor Maintenance

Auto Start Sensor Removal and Replacement

Procedures to remove and refit auto start sensors.

Section 5: Electric Motor Maintenance

Model 250-S2 Electric Motor

Maintenance for Model 250-S2 electric motor.

Other Models Electric Motor

Maintenance for electric motors in other models.

Section 6: Gear Maintenance

Model 250-S2 Gear Maintenance

Gear maintenance procedures for Model 250-S2.

Other Models Gear Maintenance

Gear maintenance procedures for other models.

Gear Timing Procedures

Procedure for timing gears for accurate alignment and performance.

Section 7: Tie Bars, Shafts, and Stripper Plates

Tie Bars, Shafts, Plates for Model 250 S2

Maintenance for tie bars, shafts, plates for Model 250 S2.

Tie Bars, Shafts, Plates for Models 250-S3, S4, 1150-S3, 1250-S3, S4

Maintenance for tie bars, shafts, plates for specific models.

Damaged Stripper Replacement

Instructions for replacing damaged stripper plates.

Cutter Shaft Assembly Replacement

Procedure for refitting cutter shaft assemblies into frames.

Section 8: LCD Operation and Features (1250 Models)

LCD Safety Features Flow Chart

Visual guide to LCD safety features and their operation.

LCD Operator Controls Flow Chart

Visual guide to LCD operator controls and their functions.

LCD Other Features Flow Chart

Visual guide to LCD features like service prompts.

Wiring Diagrams

Wiring Diagram: 250 S2

Electrical schematic for the 250 S2 model.

Wiring Diagram: 250 S3/S4/S5

Electrical schematic for 250 S3, S4, S5 models.

Wiring Diagram: 1150 S2/S3

Electrical schematic for 1150 S2 and S3 models.

Wiring Diagram: 1250 S2/S3/S4

Electrical schematic for 1250 S2, S3, S4 models.

Wiring Diagram: 1250 S5

Electrical schematic for the 1250 S5 model.

Specifications by Model

Model 250 S2 Specifications

Technical specifications for the 250 S2 model.

Model 250 S3 Specifications

Technical specifications for the 250 S3 model.

Model 250 S4 Specifications

Technical specifications for the 250 S4 model.

Model 250 S5 Specifications

Technical specifications for the 250 S5 model.

Model 1150 S2 Specifications

Technical specifications for the 1150 S2 model.

Model 1150 S3 Specifications

Technical specifications for the 1150 S3 model.

Model 1250 S2 Specifications

Technical specifications for the 1250 S2 model.

Model 1250 S3 Specifications

Technical specifications for the 1250 S3 model.

Model 1250 S4 Specifications

Technical specifications for the 1250 S4 model.

Model 1250 S5 Specifications

Technical specifications for the 1250 S5 model.

AMENDMENT RECORD SHEET