2
TEMPORARY DISABLE
On occasions where you may wish to leave a pet in your vehicle, or leave your windows down while having
optional ultrasonic sensors fitted, you can temporarily disable the trigger inputs that would cause an
unwanted
trigger i.e. you can disable
for one
arming
period
the impact
sensor, ultrasonic
or microwave sensors
if fitted, and
voltage drop sensing. The alarm will still trigger from door, boot, bonnet, and ignition inputs. To activate temporary
disable, when arming press BUTTON
1 or BUTTON 2 twice in a row with a 1 second pause
between the first & second
presses. You will be given a confirmation chirp for each press
.
EMERGENCY PANIC BUTTON
The panic feature is activated by pressing & holding BUTTON
2 on the remote- controls transmitter
for
3
seconds. If disarmed, the alarm system will arm first (i.e. lock doors)
then
the siren
will sound
& the blinkers will
flash for 30 seconds. If armed, the alarm
system
will stay armed
(i.e. the doors
will not unlock)
& the siren will
sound &
blinkers flash for 30 seconds.
To cancel
“panic”, follow
disarm
procedure
as described
on page
1.
NOTE: Panic does not work when the ignition is on by requirement of Australian Law (EPA-
Environmental
Protection Authority).
PRE-ALERT (2 STAGE) IMPACT WARNING
This special feature
provides a two-stage impact
sensing system. It gives the security conscious
owner a
sensitive car body impact sensor that will give a potential thief warning that the vehicle is protected by
this most
formidable alarm system. On detection of a low-level impact i.e. from a tyre
kick,
the
siren will
simply beep 5 times
to warn
away the would-be
thief. If the vehicle
is attacked
any further, the system
will move into full siren mode.
The
sensitivity level reference point can be adjusted to suit your needs. Please refer to the programming
section contained later in this manual.
PROGRAMMABLE
FEATURES:
The features outlined below are the most popular that can be turned on or off to suit your requirements.
Please refer to the section is this manual marked “Rhino Programmable Features” for full details.
PASSIVE ARMING: The alarm can automatically arm itself 30 seconds after you leave your vehicle
provided that the ignition is turned off, and that at least one door has been opened and closed ie. the owner
has parked and has exited the vehicle. This feature will not lock the vehicle where central locking is
connected.
AUTOMATIC RE-ARM: This feature prevents accidental disarming by the owner ie. The owner turns the
alarm off but is then distracted and forgets that they have deactivated the system. If a door is not opened,
or the ignition is not turned on within 60 seconds from when the system is turned off by the remote, the
system will re-arm, and if central locking is connected, it will re-lock the vehicle.
SILENT ARM/DISARM: This feature when turned on, stops the siren from beeping for arm & disarm
confirmation i.e. only the blinkers will flash.
LEARNING NEW REMOTES (Up to 3 remotes can be used with this alarm system)
Before
entering this mode, make sure you have all remotes present that you wish you utilise with this alarm system, as the
alarm automatically erases all remotes
when you enter this mode.
A. Arm then Disarm
the alarm system. While the system is disarmed, open and close your driver’s door (get
inside
the vehicle), making sure the interior light is coming on as you open the door.
B. Within 30 seconds, turn
the car
ignition
key from
the off position
to the ignition
on position
20 times.
30 seconds
later, the blinkers
will flash 3 times to confirm
that you have entered
the remote
learning
mode.
Repeat steps A & B if you do not receive the flashes.
D.
Now press
& hold the button
on the new
remote
you wish
to learn
in. The
siren
will beep
once
to confirm
the code has been learnt. Repeat
this step for up to 3 remotes. You can use this process
to delete lost
remote
controls by learning in the same remotes in succession to replace each of the 3 memory
locations so that the old
remote code/s are erased.
E. The system
will automatically
exit the learning
mode
15 seconds
after
the last press of a remote.
To Next Page
Loading...
