To Next PageTo Next PageWhy is my RHINO Lawn Mower not cutting material?
If your RHINO Lawn Mower is not cutting material, it could be due to excessive ground speed, so reduce ground speed. It could also be caused by RPM being too low, so use full PTO speed. Another possible cause is improper blade for direction of cut, so install blades so rotation is correct.
How to prevent blade bolts from working loose on my RHINO Lawn Mower?
To prevent blade bolts from working loose on your RHINO Lawn Mower, make sure the bolts are tightened to 600 ft./lbs. If the bolt hole is elongated or oversized, replace the blade carrier. Also, if the locknut is worn out, replace it.
Why is my RHINO Lawn Mower leaving an uneven cut?
An uneven cut from your RHINO Lawn Mower can occur for several reasons. It could be due to excessive ground speed, so reduce your speed. The blades might be worn, dull, or bent, in which case you should replace them. The mower may not be level, requiring adjustment. An improper height adjustment also could be the cause, so check and adjust the mower height. Low tractor tire pressure on one side, turning too fast or tractor tires pushing grass down can also cause this problem. Damaged mower pan can also cause uneven cut, so repair or replace as necessary.
What to do if my RHINO Lawn Mower gearbox is leaking?
If your RHINO Lawn Mower gearbox is leaking, several factors could be responsible. A damaged oil seal, bent shaft, or rough oil seal race can cause leaks, in which case you should replace the seal, shaft or repair race. The oil seal might be installed incorrectly or not sealing properly in the housing; replace the seal, or use a sealant. Other potential causes include an oil level that's too high (drain to the proper level), a damaged gasket (replace the gasket), loose bolts (tighten them), or even a sand hole in the casting (replace the castings or gearbox).
How to fix a noisy gearbox on my RHINO Lawn Mower?
A noisy gearbox on your RHINO Lawn Mower can be caused by a few things: low lubricant level (check and replenish), rough gears (run in or change gears), or a worn bearing (replace the bearing).
What to do if my RHINO Lawn Mower is leaving streaks?
Streaking while using your RHINO Lawn Mower can happen due to several reasons. The conditions might be too wet for cutting, so allow the grass to dry. Slow blades unable to cut because grass pressed down by path of tractor tires. Dull blades can also cause streaking, so sharpen or replace them. Also check if the height of cutter lower at rear or front.
Why does my RHINO Lawn Mower shear pin keep shearing?
If the shear pin on your RHINO Lawn Mower keeps shearing, it could be due to several reasons: the tractor PTO not being run at 540 RPM, so run at 540 RPM, heavy material, so reduce ground speed. Ensure you are using the recommended shear pin. Other possible causes include engaging the PTO at high engine RPM (idle engine to engage PTO), cutting in rocky conditions (increase cutting height), or the blade carrier RPM being too high (check gearbox ratios).
Why is my RHINO Lawn Mower gearbox overheating?
If your RHINO Lawn Mower's gearbox is overheating, it could be due to low lubricant (fill to level plug), using the wrong type of lubricant (replace with proper lubricant), excessive trash build-up around the gearbox (remove trash). Bearing or gears set up improperly can also cause overheating.
Why is my RHINO Lawn Mower not shredding well?
Poor shredding with your RHINO Lawn Mower could be due to excessive ground speed, so raise the front of mower relative to the rear to hold and circulate material longer. Another reason could be cutting too high, so lower the cutting height.
Why is my RHINO Lawn Mower windrowing material?
If your RHINO Lawn Mower is windrowing material, especially if it's heavy and lush, it could be due to excessive ground speed, so reduce it. Also, conditions might be too wet, so wait for them to dry.
General| Brand | RHINO |
|---|---|
| Model | TURBO 96 TURBO 96 |
| Category | Lawn Mower |
| Language | English |
