What to do if the Rice Lake Monitor display is blank when the power button is pressed?
If the Rice Lake Monitor display is blank when you press the power button, the battery may be discharged, so recharge it. Alternatively, the battery might be defective, requiring a factory replacement. A defective switch or circuit board could also be the cause, which requires authorized service.
Why does my Rice Lake MSI-8004HD toggle between Error and Button?
If your Rice Lake Measuring Instruments toggles between 'Error' and 'Button', it indicates that a key is stuck or is being held down (check switches for damage).
Why doesn't the auto total work on my Rice Lake MSI-8004HD Measuring Instruments?
If the auto total doesn't work on your Rice Lake Measuring Instruments, ensure the load is stable by waiting for the stable symbol to turn on or increase filtering for more stability. Also, the load thresholds may not be reached: weight must exceed one percent of capacity for auto total to work and must drop below 0.5% of capacity for additional weigh-ments to register.
Why is the display blank on my Rice Lake MSI-8004HD Measuring Instruments when I press the power button?
A blank display on your Rice Lake Measuring Instruments when pressing the power button can be due to several reasons: the battery may be discharged (recharge the battery), the battery may be defective (requires factory replacement), or there may be a defective switch or circuit board (requires authorized service).
Why do the setpoint lights blink on my Rice Lake MSI-8004HD Measuring Instruments?
If the setpoint lights blink on your Rice Lake Measuring Instruments, it means the set point is enabled and the trigger point has been reached. If set points are not needed, disable them.
Why won't my Rice Lake MSI-8004HD Measuring Instruments tare or total?
If your Rice Lake Measuring Instruments won't tare or total, the system may not be stable. Wait for the stable symbol to turn on. If you are in a mechanically noisy crane, increase the filtering or reduce the size of the scale increment d; It is also possible to increase the motion window.
How to fix a Rice Lake MSI-8004HD Measuring Instruments that will not zero?
If your Rice Lake Measuring Instruments will not zero, ensure the system is stable by waiting for the stable symbol to turn on. You can also increase filtering for more stability. If the zero is out of range, this may be due to limited zero range; try reducing the tension or using Tare instead.
What to do if my Rice Lake MSI-8004HD display over ranges below 100% of capacity?
If the display on your Rice Lake Measuring Instruments over ranges below 100% of capacity, it could be because tared weight/tension is added to the load to determine the overload point (return to gross tension mode). It may also be because zero requires adjustment or too much weight/tension has been zeroed (rezero the scale).
Why does my Rice Lake MSI-8004HD Measuring Instruments turn on and then immediately off?
If your Rice Lake Measuring Instruments turns on and then immediately off, it is likely because the battery is low, so recharge the battery.
What to do if Lo Batt is blinking on my Rice Lake MSI-8004HD Measuring Instruments?
If 'Lo Batt' is blinking on your Rice Lake Measuring Instruments, it means the battery is low. Recharge the battery to resolve this.
General| Brand | Rice Lake |
|---|---|
| Model | MSI-8004HD |
| Category | Measuring Instruments |
| Language | English |
Lists key features of the MSI-8004HD RF Remote Display.
Details FCC compliance information for the device.
Outlines essential safety definitions and general safety guidelines for operation.
Describes the front panel layout, including keypad and annunciator functions.
Covers unpacking, getting started, mounting, and opening the enclosure for installation.
Details wiring, power supply, radio module, ScaleCore card, and antenna installation.
Instructions for installing the tilt stand and battery options for extended operation.
Provides visual breakdowns and part lists for different generations of the remote display.
Covers powering on/off, zeroing, and taring the scale for accurate measurements.
Details printing capabilities and how to use programmable function keys for various operations.
Explains modes like Total, Net/Gross, Peak Hold, Units, and High Resolution Test.
Explains how to navigate and access the device's setup menus for configuration.
Details how to program and customize the function keys for specific operations.
Configures power-saving features like auto-off and sleep, along with display brightness and color.
Sets up operational thresholds (setpoints) and configures relay outputs for control systems.
Configures settings for operating remote scales and adjusting the weight filter for stability.
Sets up how the device accumulates and totals weighments from multiple sources.
Step-by-step guides for routine and initial calibration of the scale.
Guidelines on capacity, resolution, and setting up calibration standards.
Alternative calibration methods and gravity compensation settings for accurate readings.
Instructions for resetting the load cell calibration and returning to factory settings.
Navigating the communications menu and configuring printer output settings.
Configuring RF network settings and setting up communication with remote devices.
Managing multiple sensors, setting scanlist IDs, and configuring load totaling modes.
Setting the device's clock and understanding the hardware for communication ports.
Configuring relay outputs and selecting appropriate antenna options for RF communication.
Details on operating the Rugged Remote, including power, zero, and programmable keys.
Discusses operational considerations like signal conflicts and jamming for the Rugged Remote.
Provides solutions for common problems and lists error codes for diagnosis.
Information on safety service counters and the physical dimensions of the device.
Guides for updating device firmware and replacing the coin-cell battery for RTC.
To Next Page
