Rigaku MiniFlex 600 User Manual

Name: Rigaku MiniFlex 600
Brand: Rigaku
Rating: 4 (1 reviews)

111 pages

To Next Page

Benchtop X-

ray Diffractometer

Instruction Manual

This image is an example of MiniFlex series. The actual product may differ from the image.

Table of Contents3
Overview7
Overview of Miniflex 6007
Optical System Using SC8
Configuration9
Standard Configuration9
Names of Parts10
List of Shipped Items14
Specifications15
X-Ray Generator15
Tube Shield15
Goniometer (Angle Measuring Device)15
Detector (SC)16
Counting Control Circuit (ECP)16
Radiation Enclosure16
Cooling-Water Unit16
X-Ray Tube17
Computer (Reference Specifications)17
Standard Software17
Optional Accessories18
D/Tex Ultra High-Speed 1D Detector (Optional)18
Installation Condition19
Installation Room19
Environmental Conditions of Installation Room19
Preparing Power Supply20
Cooling Water21
Drainage21
Others21
Installation of Miniflex60023
Unpacking23
Installing the X-Ray Tube23
Connecting the Cooling Water Hose24
Installing the Scintillation Counter (SC)25
Installing the D/Tex Ultra (Optional)28
Installing the Beam Stop30
Installing and Retracting the Variable Knife Edge30
Installing the Variable Knife Edge30
Retracting the Slider32
Installing the DS and IHS (Length Limiting)33
Connecting the Power Cable33
Connecting with Computer33
Installing the Software34
Setting and Adjustment35
Types of Soller Slit, Confirming the Soller Slit35
Types of Incident Soller Slit35
Confirming the Incident Soller Slit35
Types of Receiving Soller Slit36
Optics Alignment (Required for Periodic Inspection or Installing X-Ray Tube)37
Optics Alignment (for SC)37
Optics Alignment (D/Tex Ultra)48
Optics Alignment (for D/Tex Only)56
HV/PHA Adjustment of Scintillation Counter (SC)70
Discriminator Value Setting by D/Tex Ultra73
Automatic Adjustment of Discriminator Value73
Directly Entering the D/Tex Ultra Adjustment Value75
Initial Setting of the Measurement Environment (Required When the X-Ray Tube Type Has Been Changed)77
Data Measurement and Setting Procedure for Real-Time 2 Theta Axis Correction (Required for Initial Setup or Periodic Inspection)78
Startup and Shutdown (Daily Routine)83
Starting up the System83
Shutting down the System84
Measurement of Samples (Daily Routine)85
Preparing the Sample Plate85
Preparation of Powder Sample on Aluminum Sample Plate85
Preparation of Block Sample on Aluminum Sample Plate87
Preparation of Powder Sample on Glass Sample Plate87
Cleaning Spilled or Deposited Powder Sample88
Slit System89
Slit Correction89
Measurement with Miniflex Guidance91
Maintenance97
X-Ray Tube and Scintillation Counter (SC)97
Replacing the X-Ray Tube (Procedures Required When Cleaning Filter or Replacing Tube)97
Removing and Installing the X-Ray Tube97
Disassembling the X-Ray Tube and Cleaning the Filter99
Cleaning and Further Information100
Confirming the Alarm Information101
Installing the Optional Sample Attachment103
Installing the Counter Monochromator (Optional)105
Installing the Counter Monochromator106
Optics Alignment and Notes on Monochromator109
Arrangement of Slits110

Questions and Answers:

Need help?

Do you have a question about the Rigaku MiniFlex 600 and is the answer not in the manual?

Rigaku MiniFlex 600 Specifications

General

Brand	Rigaku
Model	MiniFlex 600
Category	Measuring Instruments
Language	English

Related product manuals

Rigaku MiniFlex 600 User Manual

Table of Contents

Questions and Answers:

Rigaku MiniFlex 600 Specifications

Related product manuals