What to do if the Rinnai RD-600AU has a flame failure?
If your Rinnai Dryer experiences flame failure, first, ensure the gas supply is fully turned on. Next, inspect and clean the lint filter, back filter, and air inlet filter. If the issue persists after these steps, arrange for a service.
What to do if my Rinnai Dryer has an ignition failure?
If your Rinnai Dryer fails to ignite, verify that the gas supply is turned 'on'. Then, turn the appliance 'off' and then 'on' again. If the problem continues, arrange for a service.
How to fix filter blockages in a Rinnai RD-600AU?
To address filter blockages in your Rinnai Dryer, check and clean the lint filter, back filter, and air inlet filter.
Why has the 'time remaining' not changed on my Rinnai RD-600AU Dryer?
If the 'time remaining' display on your Rinnai Dryer hasn't changed for several minutes, especially in Automatic mode, it's because the control system is continuously recalculating the drying time based on the garment's drying rate. This is normal.
Why is there a delay after pressing the start/pause button on my Rinnai RD-600AU?
A delay after pressing the 'Start/Pause' switch before the Operating indicator shows red is a normal operation for the Rinnai Dryer. However, if the burner doesn't ignite at all, contact Rinnai.
What causes clicking noises in my Rinnai RD-600AU Dryer?
The clicking noises you hear in your Rinnai Dryer after starting or finishing a cycle are due to the expansion and contraction of burner components with heat. This is a normal operational characteristic.
Why is steam coming from my Rinnai RD-600AU Dryer discharge duct?
Steam emitted from the discharge duct terminal of your Rinnai Dryer is normal.
What to do if Rinnai RD-600AU drum keeps turning after finishing tone?
If the drum of your Rinnai Dryer continues to turn after the finishing tone, opening the dryer door will cancel the 'Extra Soft' programme.
Outlines the duration and conditions of the warranty.
Explains warranty coverage for home usage.
Explains warranty coverage for business usage.
Specifies requirements for warranty claims and service.
Lists situations and damages not covered by the warranty.
Details on buttons and indicators of the dryer's control panel.
Identifies key external components of the gas dryer.
Crucial precautions before operating, handling, and what not to dry.
General guidelines on load size and ventilation.
Advice on garment care and selecting drying cycles.
Lists fabrics and materials not suitable for the dryer.
Explains the different drying modes (General, Thick, Extra Soft, Delicate).
Lists available drying programme combinations.
How the dryer manages drying time in automatic and timer modes.
Step-by-step guide to using the dryer in automatic mode.
Step-by-step guide to using the dryer in timer mode.
Instructions for cleaning the lint filter.
Instructions for cleaning the back filter.
Instructions for cleaning the air inlet filter.
Instructions for cleaning the external parts of the dryer.
Lists and explains the dryer's safety features.
A guide to check before calling for service.
Explains normal operational sounds and behaviours.
Lists diagnostic error codes and their remedies.
Recommendations for regular servicing and contact information.
Technical details, dimensions, gas consumption, safety devices.
Key considerations for placing the dryer for installation.
Details on gas connection type, hose, and supply pressure.
Information on power connection, voltage, and wiring.
Explains floor, bench, shelf, and wall mounting methods.
Components and assembly of the wall mounting bracket.
How to attach the dryer to the wall mounting bracket.
Step-by-step guide to reversing the dryer door.
General information about exhaust duct requirements and kits.
Specifies minimum clearances for exhaust terminals.
Details on ventilation needs for enclosed installations.
Illustrates common methods for installing exhaust ducting.
Contact and location details for Rinnai's head office.
Contact numbers for sales, service, and technical information.
To Next Page
General
