ROBBE-Futaba FC-16 - FC-16 Transmitter; External Features; Fully Adjustable Stick Units; Trim Stoppers

110 pages

Save Page as PDF

To Next Page

To Previous Page

Main Page

Contents4
Description of FC-166
Specifications10
External Features12
Fully Adjustable Stick Units12
Trim Stoppers12
Removing the Transmitter Back Panel12
Inside the Transmitter14
Throttle Ratchet Spring14
Adjustable Stick Unit Tension14
Charge Socket and Batteries14
Unrestricted Selection of Channel Sequence16
Changing Batteries16
Aerial Compartment16
Changing Crystals16
Receiving System18
Recommendations on Using the System18
Operating Voltage for the Receiving System18
Operating Times18
Charging the Batteries20
Installing the Receiving System in the Model20
Servo Mounting22
Mounting a Servo on Wood22
Mounting a Servo on Aluminium, Epoxy, Etc22
Installation of the Control Surface Linkages24
Post Office Regulations26
Expanding the Transmitter28
Main Circuit Board28
Optional Expansion28
Mixer Switches28
Installing Modules30
MIX Trimmer Modules30
Connections30
Multi-Switch, Multi-Prop Modules30
Installation and Connections32
Using Campac Modules32
Mixer Programs32
Transmitter Tray34
Repairs and Servicing34
Splined Servo Output Devices36
Adjusting the Neutral Position36
Using and Programming the Transmitter38
Display38
Keypad38
CURSOR Keys38
Why Program?40
The Route to the Function You Require40
Calling up a Function40
Using the System for the First Time42
Locating a Particular Function42
Adjusting a Function42
Power-On Display42
Standard Functions44
Description of the Functions46
Model Memory Select46
Selection46
Model Name46
Servo Reverse48
Dual Rates48
Dual Rates Switches50
Programmable Mixers50
Auxiliary Trim (Sub-Trim)52
Multi-Switch, Multi-Prop54
Fail Safe54
Hold Mode54
Basic Adjustments (Parameters)56
Erasing Data (Para,Reset)56
Stick Mode56
Dual Rate Switches58
Full Throttle Forward/Back58
Modulation58
Selecting Mixer Programs60
Copying Model Memories60
Trim Memory60
Stopwatch, Timer60
External Trimmer Volume62
Low Voltage Warning Display62
Initialising a Campac Module62
MIX-Program64
Connecting Servos to the Receiver64
Description of Universal Mixer Program Functions66
Aileron Differential66
Flaperon Mixer66
Delta Mixer68
V-Tail Mixer70
Flaperon Trim70
Combi-Switch72
Flaperon - Elevator Mixer74
Adjusting Elevator Compensation74
Offset74
Airbrake - Elevator Mixer76
Crow Mixer76
Function Change Channels 3 + 578
HELI Mixer Program80
A Bried Introduction to Model Helicopter Technology80
Servo Connections for the HELI Mixer Program80
Collective Pitch80
Tail Rotor82
Gyro82
Pitch-Axis82
Roll82
Description of the HELI Mixer Program Functions84
External Trimmers84
Tail Rotor Compensation Revolution MIX86
Constant Rotor Speed86
Collective Pitch Minimum86
Collective Pitch Maximum (High Pitch)88
Hover Throttle88
Hover Collective Pitch90
Collective Pitch Trim90
Idle up92
Auto-Rotation Throttle Hold92
Swashplate Type94
Exponential Control Curve105
Setting the Curve105

Related product manuals

ROBBE-Futaba F-14

5 pages

ROBBE-Futaba FX-18 NiMH

56 pages

Skysport T4YF 2,4 GHz

96 pages

ROBBE-Futaba FC-16 - FC-16 Transmitter; External Features; Fully Adjustable Stick Units; Trim Stoppers

Table of Contents

Related product manuals