ROBEL 62.05L - User Manual

Questions and Answers

D
drobertsAug 2, 2025
How to start a ROBEL Vibratory rammers & tampers when the engine will not start?
- S
  svaldezAug 2, 2025
  If your ROBEL Vibratory rammer & tamper engine won't start, several factors could be the cause. First, ensure that there is enough fuel. If the engine is not getting fuel, refuel it. Second, make sure the choke is properly engaged by closing the choke lever and pushing the primer pump. Third, a spark plug wet with fuel (flooded engine) or oily may be the problem. In this case, clean the spark plug. Finally, a clogged fuel filter can prevent the engine from starting, so clean the fuel filter.
S
Spencer HardyAug 6, 2025
Why does my ROBEL Vibratory rammers & tampers engine become very hot, with low performance?
- J
  John SalinasAug 7, 2025
  If your ROBEL Vibratory rammers & tampers engine is overheating and has low performance, it could be due to a few reasons. First, the carburetor setting may be too lean, so adjust it according to the actual altitude above sea level. Second, a clogged fuel filter can cause overheating, so clean the fuel filter. Third, check the oil level; if it's too low, this can lead to overheating.
A
Aaron CollinsAug 11, 2025
What to do if my ROBEL Vibratory rammers & tampers engine runs not smoothly, with low performance?
- M
  Maxwell LeeAug 11, 2025
  If your ROBEL Vibratory rammers & tampers engine is not running smoothly and has low performance, consider these potential causes. The carburetor setting may be too rich, so adjust it according to the actual altitude above sea level. Also, a clogged air filter can cause these issues, so clean the air filter.
L
Laura PowellAug 14, 2025
Why does my ROBEL Vibratory rammers & tampers engine stop at idle?
- A
  Angel MillerAug 15, 2025
  If the engine of your ROBEL Vibratory rammers & tampers stops at idle, the idle setting might be too low. To fix this, adjust the idle setting.
M
Michele SinghAug 19, 2025
What to do if the tamping pick does not vibrate on my ROBEL Vibratory rammers & tampers?
- N
  Natasha GreeneAug 19, 2025
  If the tamping pick on your ROBEL Vibratory rammers & tampers isn't vibrating even when the engine is running at high RPM, the coupling element between the engine and eccentric shaft may be defective. To resolve this, change the coupling element.
T
Timothy NelsonAug 23, 2025
Why are the rubber buffers ripped on my ROBEL Vibratory rammers & tampers?
- A
  avilaelizabethAug 23, 2025
  If the rubber buffers on your ROBEL Vibratory rammers & tampers are ripped, it is likely due to wear. Replace the rubber buffers.
S
sean84Aug 27, 2025
What causes a worn tamping tool on ROBEL Vibratory rammers & tampers?
- J
  Jordan RiveraAug 28, 2025
  If the tamping tool on your ROBEL Vibratory rammers & tampers is worn, it is likely due to wear. Replace the tamping tool.

Summary

General Information

About These Instructions

Explains symbols used for operating procedures and lists.

General Regulations

Outlines legal requirements, accident prevention, and buyer responsibilities.

Intended Audience for Operating Manual

Defines the target audience and prerequisites for using the manual.

Liability Exclusions

Details manufacturer's exemptions from liability for improper use.

Copyright

States the intellectual property and usage rights of the product.

Acceptance and Operating Licence

Covers buyer's responsibility for checking goods and meeting regulations.

Validity of Instructions

Lists EDP numbers for which these instructions apply.

Safety

Designated Use

Specifies the vibratory tamper's intended use in track construction.

Foreseeable Misuse

Warns against using the tamper for demolition work.

Conventions of Layout

Explains warning texts and symbols used in the manual.

Design Changes and Original Parts

States manufacturer's non-liability for unauthorized changes and non-original parts.

Protective Devices

Emphasizes the importance and proper use of safety devices.

Safety Regulations

Lists essential regulations to be observed for safe operation.

Qualifications of Staff

Defines requirements for personnel operating and maintaining the product.

Personal Protective Equipment

Specifies required personal protective equipment for operation and maintenance.

Information on Specific Dangers

Details specific hazards like heavy weight, unergonomic operation, and combustion engines.

Accident Prevention

Outlines measures for preventing accidents and ensuring safe operation.

Fire Safety

Provides guidelines for fire prevention and extinguishing.

Technical Data

Drive

Engine type and performance specifications.

Dimensions

Physical dimensions of the tamper.

Filling Quantities

Required fuel and oil quantities for the machine.

Weight

Total weight of the tamper.

Environmental Conditions

Covers temperature and altitude operating ranges.

Temperature

Operating, transport, and storage temperature limits.

Operating Altitude

Specifies operating altitude limits for the machine.

Noise Emissions and Vibration

Provides data on sound levels and vibration.

Noise Emissions

Details the sound pressure and power levels.

Vibration

Details total vibration levels.

Digital Tach;Hour Meter

Explains the specifications of the tach/hour meter.

Description of Machine

Design

Describes the main components of the vertical tamper.

General View

Provides an overview of the machine with labeled parts.

Work Station

Describes the operator's stance and grip during operation.

Petrol Engine

Details the petrol engine components and their locations.

Signs and Labels

Identifies various signs and labels on the machine.

Digital Tach;Hour Meter

Explains the function and display of the tach/hour meter.

Accessories

Lists available accessories for the machine.

Preparing the Machine

Digital Inductive Tach;Hour Meter

Covers operation and settings for the tach/hour meter.

Checking;Adjusting the Carburetor Setting

Details how to adjust the carburetor for different altitudes.

Checking the Petrol Engine

Explains how to check engine oil level and air filter.

Engine Oil Level

Guides on checking and maintaining the engine oil level.

Operation

Starting the Engine

Step-by-step guide to starting the tamper's engine.

Working with the Tamper

Instructions on how to operate the tamper effectively.

Tamping (Sleeper)

Details the process of tamping around sleepers.

Tamping (Track Panel)

Explains tamping procedures for track panels.

Stopping the Engine

Procedures for safely shutting down the engine.

Installing Rail Movement Indicator

Instructions for fitting the rail movement indicator accessory.

Transport and Storage

Transport

Guidelines for transporting the tamper safely.

Storage

Procedures for storing the tamper correctly.

Troubleshooting

Error Analysis and Remedies

Lists common errors, their causes, and remedies.

Maintenance

Maintenance Schedule

Provides a schedule for routine maintenance tasks.

Cleaning and Care

Gives instructions for cleaning and maintaining the product.

Engine

Covers engine maintenance procedures.

Cleaning the Air Filter

Details how to clean the air filter.

Cleaning the Fuel Filter

Explains the procedure for cleaning the fuel filter.

Maintaining the Spark Plug

Covers spark plug inspection, cleaning, and gap adjustment.

Idle Adjustment

Guides on adjusting the engine idle speed.

Reset Carburetor to Factory Setting

Explains how to reset the carburetor to its original settings.

Changing the Oil

Provides instructions for changing the engine oil.

Changing Fuel Pipe

Details the process for replacing the fuel pipe.

Rubber Buffers

Covers checking and replacing rubber buffers.

Checking the Rubber Buffers

Explains how to inspect rubber buffers for wear.

Replacing the Rubber Buffers

Guides on how to replace worn rubber buffers.

Centrifugal Clutch

Details maintenance for the centrifugal clutch.

Tamping Tool

Covers inspection and replacement of the tamping tool.

Checking the Tamping Tool for Wear

Explains how to check the tamping tool for wear.

Replacing the Tamping Tool

Guides on how to replace the tamping tool.

Changing Bearings

Details the process for changing bearings.

Signs and Labels

Covers checking and replacing signs and labels.

Environmental Protection and Disposal

Environmental Protection

Outlines environmental protection measures during use and maintenance.

Disposal

Provides guidelines for proper product disposal.

Appendix

EC Declaration of Conformity

Includes the EC Declaration of Conformity document.

ROBEL 62.05L Specifications

General

Brand	ROBEL
Model	62.05L
Category	Vibratory rammers & tampers
Language	English

ROBEL 62.05L - User Manual

Table of Contents

Questions and Answers

Summary

General Information

About These Instructions

General Regulations

Intended Audience for Operating Manual

Liability Exclusions

Copyright

Acceptance and Operating Licence

Validity of Instructions

Safety

Designated Use

Foreseeable Misuse

Conventions of Layout

Design Changes and Original Parts

Protective Devices

Safety Regulations

Qualifications of Staff

Personal Protective Equipment

Information on Specific Dangers

Accident Prevention

Fire Safety

Technical Data

Drive

Dimensions

Filling Quantities

Weight

Environmental Conditions

Temperature

Operating Altitude

Noise Emissions and Vibration

Noise Emissions

Vibration

Digital Tach;Hour Meter

Description of Machine

Design

General View

Work Station

Petrol Engine

Signs and Labels

Digital Tach;Hour Meter

Accessories

Preparing the Machine

Digital Inductive Tach;Hour Meter

Checking;Adjusting the Carburetor Setting

Checking the Petrol Engine

Engine Oil Level

Operation

Starting the Engine

Working with the Tamper

Tamping (Sleeper)

Tamping (Track Panel)

Stopping the Engine

Installing Rail Movement Indicator

Transport and Storage

Transport

Storage

Troubleshooting

Error Analysis and Remedies

Maintenance

Maintenance Schedule

Cleaning and Care

Engine

Cleaning the Air Filter

Cleaning the Fuel Filter

Maintaining the Spark Plug

Idle Adjustment

Reset Carburetor to Factory Setting

Changing the Oil

Changing Fuel Pipe

Rubber Buffers

Checking the Rubber Buffers

Replacing the Rubber Buffers

Centrifugal Clutch

Tamping Tool

Checking the Tamping Tool for Wear

Replacing the Tamping Tool

Changing Bearings