Rockwell
TM
1. Key
2. Cylinder or Cyl. housing and cylinder
3. Cylinder Backplate
4. External Pull Assembly
5. Deadbolt Mounting Plate
6. Deadbolt Mounting Screws
7. Spindle
8. Spindle Collar
9. Latch Mounting Plate
10. Internal Deadbolt Plate Assembly
11. Oval Head Machine Screws
12. Latch Mounting Plate Screws
13. Screw Washer
14. Flat Head Machine Screw
15. Screw Cover
16. Latch Rosette
17. Plastic Washer
18. Lever
19. Set Screw
20. Rosette Pick
21. Allen Wrench
22. Right Hand Spindle Cartridge (LEFT
hand spindle Cartridge Pre-installed)
23. Tapping Screw
EXPLODED VIEW
1. Door Preparation
A.Measure thickness of your door.
Ensure door is at
least 1-3/4" thick. If door thickness is less than
1-3/4" DO NOT PROCEED WITH
INSTALLATION.
B.Fold the marking template for the handle set
on the line and place on the door aligning A and
B of the template with the double bore of door.
Locate and mark hole E with a pencil. Carefully
drill hole E perpendicularly (at a 90°) to door
with a 3/8" drill bit.
IMPORTANT: Double check hole E location
before drilling .
2. Determine the handing of your door. Standing
on the outside of the door, if the hinges are to the
left of the door then the door is left handed
and if the hinges are to the right of the door then
the door is right handed. Handle sets are supplied
with left and right hand spindle cartridge to
work on both left and right hand doors
3. The handle sets are preset to work with a Left hand door,
should you have a right hand door, the left handed spindle
cartridge will need to be switched to a right hand spindle
cartridge. Right Hand Spindle Cartridge (included) has
instructions on changing from
left to right hand
. For Left hand
doors please proceed to step 4. For Right hand doors, please
replace the spindle cartridge to the correct hand prior to
proceeding to step 4.
The handle set will not work if the
incorrect cartridge is installed .
Savoy
Windsor
16
19
17
10
12
13
14
15
8
9
18
20
21
7
2
1
2
2
5
6
11
22
3
23
4
If door thickness is less
than 1-
3
4
"do not install
the spindle collar
4.
REQUIRED TOOLS
-Protective Eyewear
-#2 Phillips Screwdriver
-Pencil
-
1
8
" Drill Bit
MULTIPOINT HANDLE SET
INSTALLATION INSTRUCTIONS
OUTSIDE
OUTSIDE
HINGE
HINGE
LEFT HANDED DOOR
RIGHT HANDED DOOR
LEFT
HAND DOOR
(PREINSTALLED)
RIGHT
HAND
DOOR
86-MPMHS-903 REV. B1 / 2
BEFORE YOU BEGIN
Check door thickness as handle will work with
a 1-
3
4
" thick door only. If door thickness is
greater than 1-
3
4
" up to 2-
1
4
" thick please
contact Rockwell Security Inc.
Remove and discard all packaging materials
and verify you have all the parts in the
exploded view section of instructions
Follow step by step installation instructions
to ensure proper operation of handle set.
Always wear protective eyewear.
(2) DEADBOLT MOUNTING SCREW
#10-32 x 2"
(2) 7/8 " OVAL HEAD MACHINE SCREWS
#8 x 7/8"
(2) MOUNTING PLATE SCREWS
#8-32 x 1-1/2"
(1) FLAT HEAD MACHINE SCREWS
#8-32 x 2-1/2"
(2) SET SCREWS
1/4"-20
(1) TAPPING SCREW
#8 x 1"
B
A
E
SPINDLE
COLLAR
SHORT
END
INSIDE
4. Slide the spindle collar onto the long end of the
spindle. If door thickness is less than 1-
3
4
" spindle
collar is not required.
From the inside of the door
insert the short end of the spindle into the latch
hub
of the lock ensuring the groove side of the long end
of the spindle is facing down. If door thickness is 1-
3
4
",
then also install the spindle collar onto the long side
of the spindle
.
SPINDLE
SPINDLE
GROOVE SIDE
FACING DOWN
LONG
END
Spindle Collar
Short end
LONG END
To Next Page
Need help?
General