Roland HP 730 - Page 40

switching on the piano, then the MT-120, the
piano automatically selects Local Off.
Setting the Transmit Mode
There are two Transmit modes for sending MIDI
messages. Select the one that suits your purpose.
* Note and Pedal messages can be transmitted
and received in any mode.
Display Transmit Mode
1 Mode 1
This mode allows the piano to transmit only the
performance messages (information concerned with
playing the keyboard or pressing the pedals) to the
external MIDI device.
Even if you change Tones on the piano, Tone Selection
messages (Program Change) are not transmitted.
2 Mode 2
This mode allows the piano to transmit various setting
messages, along with the normal performance
information. When you select a new Tone, the
corresponding Program Change will be transmitted.
This mode may be convenient when recording
performances into a sequencer.
1. Press the Chorus button while holding the
Transpose button down,
2. Select the Transmit Mode with the |+/-]
buttons,
3. Press the Transpose button and confirm that
the indicator goes out.
The Transmit Mode you have selected here will
be retained until the piano is switched off.
When the piano is switched on, MODE 1 will be
automatically selected.
Mode bs 2
MIDI Messages Transmit Transmit
Note Message ° °
Program Change Message *] o
Control Change Message
Volume (7) x x
Damper (64) ° o
Sostenutto (66) fe) °
Soft (67) ° o
Expression (11) ° oO
Chorus On/Off (93) x fey
Reverb On/Off (91) x o
Master Tune (RPN) x o
Roland Exclusive Message
Temperament Selection
Stretch Tuning Selection
Dual Balance Selection
Chorus Depth Selection
oO
te)
o
x KK
38
Reverb Depth Selection x °
Pedal Resonance Amount Selection x °
* *1; No message will be transmitted by selecting
a new Tone on the piano.(See Transmitting and
Receiving Program Changes)
Transmitting and Receiving
Program Changes
Transmitting
Program Changes can be transmitted as follows:
1. Press the Reverb button while holding the
Transpose button down.
2. Press the Reverb button again, and the display
shows the Group, Bank, and Number.
3. Set the Program Change Number with the [+/-
] buttons.
4. Press the Transpose button and confirm that
the indicator goes out.
The Program Change you have set will be
retained until the piano is switched off.
Group A
Number
123 4 5 6
3
|~w]~
9| to] 11} 12] 13] 14] 1
a a
17] 18} 19 20] 211 22] 23| 24
25] 26} 27) 28) 29] 30) 31| 32
37 39
41 42} 43) 44) 45] 46) 47| 48
49 50| 51] 52| 53] 54] 55] 56
57 |58 | 59 | 60 | 61 | 62 | 63 | 6a
SIKH OR —
2
8
2 @ B eg 8 eS 8
rs
SiN 4
Number
3°45 6 7 8
65| 66] 67; 68) 69; 70; 7
73) 74| 75 78
76| 77|
at| 82] 3] 84] a5] gs] 87] 88
aa| 80] 97 92] 93] 94] 95! 96
91001101
105) 106 107] 108] 109) 410) 111] 112
143} 44) 445] 146] 117] 418] 119] 120]
122/123] 124] 725/126 127/128)
ovon awn
of
g
© 8
3 8 2
2.
3 2
B