Roland HP 730 - Connecting with a Computer

Receiving
When the piano receives a Program Change
Number, the corresponding Tone will be selected
as shown in the following list. When the Transmit
Mode 2 is selected, the Program Change that
corresponds to the Tone will be transmitted.
Program Change Tone
1 Pianol
2 Piano2
4 Harpsichord
a Vibraphone
6 Electric Pianol
7 Electric Piano2
8 PipeOrgan
9 Strings
10 Pianol+Piano2
11 Pianol+Harpsichord
12 Pianol+Vibraphone
13 Pianol+Electric Piano!
14 Pianol+Electric Piano2
15 Pianol+PipeOrgan
16 Pianol+Strings
17 Piano2+Harpsichord
18 Piano2+Vibraphone
19 Piano2+Electric Pianol
20 Piano2+Electric Piano2
21 Piano2+PipeOrgan
22. Piano2+Strings
23 Harpsichord+Vibraphone
24 Harpsichord+Electric Pianot
25 Harpsichord+Electric Piano2
26 Harpsichord+PipeOrgan
27 Harpsichord+Strings
28 Vibraphone+Electric Piano]
29 Vibraphone+Electric Piano2
30 Vibraphone+PipeOrgan
31 Vibraphone+Strings
3 Electric Pianol+Electric Piano2
33 Electric Pianol+PipeOrgan
34 Electric Pianol+Strings
35 Electric Piano2+PipeOrgan
36 Electric Piano2+Strings
37 PipeOrgan+Strings
38 Acoustic Bass/Pianol
39 Acoustic Bass/Piano2
40 Strings / Harpsichord
4] Acoustic Bass/ Vibraphone
4Q Acoustic Bass/Electric Piano]
43 Acoustic Bass/Electric Piano2
44 PipeOrgan/Harpsichord
45 Strings/Pianol
* 10 - 37 are for Dual Play, while 38 - 45 are for the
Split mode.
* 3, and 46 - 128 will be ignored.
Connecting with a Computer
The HP 730/530e/330e is equipped with a
Computer connector. By connecting a cable
between this connector and the serial port on a
computer, performance information can be
communicated between the piano and the
computer.
1. Switch off the piano.
2. Connect a computer cable (RSC-15APL/RSC-
15AT/RSC-15N: optionally available) between
the serial port on the computer and the
Computer connector on the piano.
3. Set the Computer switch on the piano to Mac,
PC-1, or PC-2.
4. Match the baud rate (data transmission speed
used by the computer and the HP-
730/530e/330e) of the computer and the
software.
Setup Examples
Setup for the Apple Macintosh Series
Connect the Modem Port (or Printer Port) on the
Apple Macintosh Series to the Computer
connector on the piano using the computer cable
(RSC-15APL:; optionally available), then set the
Computer switch to Mac.
Use Patch Bay on the Apple Macintosh to set the
Interface Type (clock of the MIDI Interface) to 1
MHz.
Setup for the IBM PC
Connect the serial port (such as COMI or COM2)
on the IBM PC with the Computer connector on
the piano using a computer cable (RSC-15AT:
optionally available), then set the Computer
switch to PC-2.
Then, set the Computer switch so it matches the
Baud Rate of the software to be used.
When the baud rate is 31.25 kHz, set it to PC-1,
and when it is 38.4 kHz, set it to PC-2.
* For further information about the baud rate
setting, refer to the owner’s manual for the
software you use.
If necessary, modify the MIDI Transmit Channel
{p. 36 ) or Local On/Off (p. 37).