Table of Contents
Before You Begin
3
Features
3
About
the Conventions
Used in This Manual 3
About the Screen Displays
3
Panel Descriptions
6
Important
Notes
8
Quick Start
1. Getting
Ready to Play
10
Connecting with
Audio Equipment
10
Turning On the Power
11
Turning
Off the Power
11
2.
Playing the Demo
Songs (ROM Play) 12
3. Auditioning the
Sounds
13
4. Changing
Sounds (Patches)
15
5. Saving
Sounds and Settings
18
Chapter
1
—
Overview of the jv-iaBo
1.
Units of
Sound
20
The
Smallest Units of
Sound —Tones 20
Combinations of
Tones That Make Soimds
—
Patdies
20
Play Percussion Instruments
Assigned to Each Key
—
Rhythm Sets
21
Assigning Patches and
a Rhythm Set Equivalent
to 16
Devices
—
Performances
21
Using Performances
22
2.
Sound Module and
Memory
23
3. Modes on the JV-inBD
24
4. About the Effects
25
5. Concerning Tone
Editing
26
Chapter 2
—
Basic
Operation
1. Choosing
a Mode
28
2. Play
29
Choosing a
Sound
29
Using Cards and
Expansion
Boards
31
Choosing the Tones
and Parts to Play
31
Changing
the Pitch of a Sound
—
Octave Shift 32
3.
Editing
33
Entering the
Edit Mode
33
Choosing
the Tones and Parts
to Edit
33
Moving the Cursor
and Changing
Settings 35
Changing Pages
36
Editing
a Patch While
in the Performance Mode
37
Switching Effects
On and Off
38
Confirming
Current Settings
or MIDI Information
—
The Information
Function
38
Chapter
3
—
JVIodes
and Parameters
1. Patch Edit Mode
42
Making Settings for an Entire
Patch (COMMON)....42
Selecting Effects Added
to the Patch (EFFECTS) 44
Using Controllers to Change How
Sounds Are Played
(CONTROL)
47
Selecting Waveforms (WAVE)
50
4
Adding Undulations to
a Sound (LFO) 51
Changing
the Pitch (PITCH) 52
Changing the Sound (TVF)
53
Changing
the Volume (TV
A)
55
2. Perfonnance Edit
Mode 57
Making Settings
for an Entire Performance
(COM-
MON)
57
Selecting
Effects Added
to the Performance
(EFFECTS)
57
Setting the MIDI
Charaiel for a Part (MIDI)
59
Selecting the Patch
Assigned to a Part (PART)
60
Setting the Pitch for a Part (PITCH)
60
Setting the Stereo
Position for a Part (PAN)
60
Setting
the
Volume for a Part (LEVEL)
60
3.
Rhythm
Edit Mode
61
Naming a Rhythm
Set (COMMON)
61
Selecting Effects Added
to the Rhythm Set (EFFECTS) 61
Using Controllers to
Change How Sounds
Are Played
(CONTROL)
63
Selecting Waveforms
for a Rhythm Tone
(WAVE) ..63
Changing the Pitch
of a Rhythm Tone (PITCH) 64
Changing the
Sound of a Rhytlim
Tone (TVF) 64
Changing
the Volume of a Rhythm
Tone (TV
A)
65
4. System Mode
66
Making
Selections for
Settings and the
Display
(SETUP)
66
Making Settings
for MIDI (MIDI)
66
Adjusting the
Tuning (TUNE)
68
Using the
JV-1080's
Controls to Play
Test Sounds
(PREVIEW)
69
5. Utility Mode
70
Saving the Data
You've Created (WRITE)
70
Copying Data
(COPY)
71
hiitiaUzing Data (INITIALIZE)
72
Protecting
Data (PROTECT)
72
Using a DATA
Card (CARD)
72
Copying
a Specific
Range of Data
(BLOCK COPY) .74
Sending
Data to an
External MIDI Device
(BULK
DUMP)
74
Returning
Settings to Their
Factory Defaults
(FACTO-
RY PRESET)
74
Chapter
4
—
Other Functions
of the
JV-
10B0
1.
Using the
JV-1080
with a DTMS
(playing
back
GM
scores)
76
Selecting
GM mode
76
Initializing
GM mode
76
2. Enhancing
Musical Expression
in
GM mode ...77
Adjusting
the Effects
71
Selecting a Patch for
each Part (PART)
78
Adjusting
the Pitch
of each Part
(PITCH) 78
Adjusting the
pan position of
each Part (PAN) 78
Adjusting
the volume
of each Part (LEVEL)
78
3. Live
Perfonnance
Techniques
79
Selecting
JV-1080
sounds from
an external device ...79
To Next Page
Loading...
