Roland M-GS64 - Page 40

Eee r eee eee a TE a TES
« RPN MSB/LSB (Controller number 100,101)
Status 2nd byte Sed byte
Bali 65H mH
Ball bd M4
nail} channel number 2 OH FH ch. - ch 36)
mme=upper byta of porameter number specitied by RP
i=lower byte of porometer number specified by RPH
+ This messoga Is not received when Rx.RPN = OFF,
~ Tho value specified by RPN will nol be reset even by messages such as Program Change or Reset All Contralier.
“-RPNY?
The RPN (Registered Parameter Number} messoges are expanded control changes, ond each function of on RPH is
described by the MIDI Standard.
To use these messoges, you must first use RPN MSB ond RPN LSB messages to specify the porameter to be controlled,
nd then use Dato Emry messeges to specify the value of the specified porameter, Once on RPH porameter has been
specified, ull Dato Entry messages received on thet channel will modify the volue of that parameter. Ts prevent acci-
dons, itis recommended that you ses RPH fiull (RPM Number = 7FH/7Fh} when you have finished setting the value
of the desired porometer.Refer to Section 5, “Examples of actual MID! messages” <Example 4> {Page 50).
On the M-G564, RPN con be used 10 modify the follawing porameters.
RPH Onto entry
AMSB_LSE AASBISG Explanation
OOH OOH mmH— Pitch Bend Sensitivity
am: OOH - 18H {0 - 24 semitones} {nitial value = 02H (2 semitones}
Il: ignoted (processed os OOH}
specity up fo 2 octaves in semitone sleps
OOH O1H ml HH Mostet Fine Tuning
ml: 00 OOH - 40 008 - 7F 7FH
(-100-0-+99.99 cents)
Refer to 5. Supplementary material, “About tuning”.
OOH 02H mmH—- Master Coarse Tuning
mm: 2BH - 40H - 58H (-24 - 0 - +24 semitones}
Ni: ignored (processed as OOH}
TRH FH —— RPN mull
set condition where RPH ond NRPH ote unspecified.
‘The date entry messages after set RPN null will be ignored. (No Data entry messages
‘ore required ofter RPH null).
Settings already made will not change.
mini; ignored
Program Change
Stotus 2nd byte
{nl ppl
2 OH FH {ch ] - ch.16}
+ OOH - 7FH iprog.} - prog.128)
n=AIDI channel number
pp=Program aumber
* Not received when Rx.PROGRAM CHANGE = OFF. {Initial value is ON)
” Alter o Program Change message is received, the sound wili chonge beginning with the next Note-on. Voices
olready sounding when the Program Change messous wos seceived will nol be affected.
* For Drum Parts, Program Chonge messages will not be received on bank numbers 129 - 163B4 {the value of
Control Number 0 is other than OL00H}),
Channel Pressure
Status 2nd byte
Ont wht
2H - FH Ach. - ch.16)
:O0H - 7FH (0 - 127)
nsMiDi chonnel number
weChonnel Pressure
* Not received when Rx.CH PRESSURE (CAF) = OFF. (Initio! valve is ON}
* The resulting effect is determined by System Exclusive messages. With the initial settings there will be no effect.
Pitch Bend Change
Status 2nd byte Sed byte
Endl tH mmti
2 OH- FH (ch.} - ¢h.16}
+00 OOH - 40 OOH - 77 7FH (-8192-6- +8191)
n=/AID! chennel number
mm, ll=Pitch Bend valve
* Not received when Rx. PITCH BEND = OFF. (Initial value is ON}
"The resulting effect is determined by System Exclusive messages. With the initfol settings the effect is Pitch Bend.
38
Channel Mode Messages
All Sounds Off = (Controlier number 126)
Srows Ind byie dd byte
Bn 788 0K
a=MID} channel number OH - FH {ch.] - ch. 76)
* When this messoge i received, cll currenily-souncing notes on the corresponding chonnel wil be turned off imme-
diately.
Reset All Controliers (Controlier number 121)
Sows 2nd byte ard byte
Enki 75K OOH
= HMID! chennel number 2OH- FH ch}. ch6)
* When this message is received, the following controllers will be set to their reset values.
Pitth Bend Chonge tO trenter)
Polyphonic Key Pressure O {ofl}
Gaannal Pressure O {olf}
Hodulation O {cH}
Expression 127 (mux)
Hold 1 G {off}
Fortomento O {off}
Sostenuto O {off
Soft O (ctf)
RP unset; previously set data will not change
HRPN unset; previously set dato wil not change
Ali Notes Off {Controfier number 123)
Bn TBH OOH
n= MIDI chonnel number OH FH (cht - ch.16)
When All Notes Off is received, olf notes on the corresponding channel will be tumed off. However if Hold 1 or
Sostenuis is ON, the sound will be continued untill these are turned aff.
OMNI OFF (Controlier number 124)
Status 2nd byte 3rd byte
Bn 7H OOK
n=HID! chonnel number 7 OH- FH (cht - ch.16}
* The some provessing will be carried out os when All Notes Off is received.
OMNI ON (Controller number 125)
Stotus Ind byte 3rd byte
Balt 70H OOH
n=HAIDI channel number OH - FH (cht - chi.16)
* OMNI OH is only recognized as “All notes off"; the Mode doesn't change (OMNI OFF remains),
MONO (Controller number 126)
Siotus «Ande «id bvte
Bal TEH mnt
n=MAlDichanne! number
mm=mone number
2 OH - FH fehl - ch.16)
2 OOH - LOH (G - 16}
* The some processing wil be cortied ovt as when All Sounds Off and Alt Notes Off is received, and the corresponding
channel will be set to Mode 4 {M=1) regardless of the value of “mono number”.
POLY {Controller number 127)
Stotus andbvie Sed bute
Batt THK OOH
=MIDi chennsl number 20H - FH fehl - ch.l6)
* The some processing will be corried out os when All Sounds OF ond All Notes Off is received, end the corresponding
chonnel will be set to Mode 3.