Roland M-GS64

nna
TT
a
ae
eae
need
¢ Patch Port parameters
The M-G5E4 hos 16 Parts in Group A and 1é Parts in Group 8, Parometers thet con be set individually for each Part are called Patch Port porameters.
{F
you
use
exclusive
messuges
to
set
Potch
Port
parameters,
specify
the
oddress
by
Block
number
rather
than
Part
Number
{normally
the
some
number
os
the
MIDI
chonnell.
The
Block
number
con
be
spacified
os
one
of
16
blocks,
{rom
O(H}
ts
FH},
To specify o Port of group A, use the Block number corresponding {0 the Port and specify an address of 40 7*
‘vio PORT A (normolty MID! HN A),
To specify « Port of group 8, use the Block number corresponding to the Port and specify an address of 40 ** ** via PORT B (normally MIDI IN 8).
To specify o Part of either group A or B frome single PORT, soecify an oddress of 40 °* “* for group A Parts or an sddress of 50° "* for group B Parts when using PORT A.
Conversely,
to
specily
o
Port
of
either
group
A
cr
B
from
PORTS,
specify
on
address
of
$0
**
**
for
group
A
Paris
ot
an
address
of
40
°*
**
for
group
B
Parts.
in
other
words,
when
specifying
Paris
of
the
opposite
side
os
the
PORT
being
used,
use
oddresses $0 °° **,
The relation between Patt umber snd Block number is as follows,
* x. BLOCK NUMBER (0 - F,
Port} (default MIDIch = 1}
Port 2 (default iIDick = 2)
Part 9 (defoul MIDKh = 9}
Port 0 {default MiDIch =10}
Petit {default MiDich =1)}
* nAIDE chon! namber (0 - F} of the BLOCK,
(0.00 62 00. 7F
40 1x00
40 x Ole 00. 7F
1x02 060091 00-10
40x03 69000) 00-04
4G ix04d 000001 09.01
40x05 60060) 00-61
401.06 600007 66-01
40 ix O? 00-0003 00-0
40x08 C000 07 0. OF
401x09 0096.07 00-01
40% 0A 00 0001 00-01
"When “Genero MID! System On” i
40 ix 08 000001 00-0
AGixOC = 4000.01 0-61
401,00 08006) 00-01
40 tx GE 000001 00-0
4G ix OF = 006001 00-01
4Q1x10 000001 00-61
40ixti 00009) oO.
40ix12 030001 06-01
404213 000007 00-6)
40x14 000001 0-02
* ASSIGN MODE is
general purposes there is no need to change
4Q\x15 C0001 00-02
*
This
porameter
sets
the
Drum
Mop
of
the
Port
used
os
the
Brum
Port.
The
M-G564
can
simultaneously
(in
different
Parts}
use
up
to
two
Drum
Maps
{MAPI,
MAP2).
With
the
iniiia!
settings,
Port}
(MID!
CH=10,
x0)
is
set
fo
MAPI
[1],
ond
other
this.
USE FOR RRYTHM PART
Ports ate set to cormal insirumentel Paris (OFF(O)}.
44
O = OFF
T= MAPI
2 = MAP
00 stx=/0
GT atx=
Part)? (default MIDIch =12) x=B
Portlé (default MIDIch =16) x=F
Purnmeter
Descrintion,
Default
Yolue
{H)
Description
TONE NUMBER CG#00 VALUE 0-127 oO 0
PLC. VALUE 1-128 a i
Rx. CHANWEL 1-16, OFF Some as the Fort Numbet
Rx. PITCH BEND OFF / ON H ON
Rx. CH PRESSURE CAF) OFF / ON a ON
Rx, PROGRAM CHANGE GFF / ON ah On
Rx. CONTROL CHANGE OFF / ON or ON
Rx. POLY PRESSURE(PAN} OFF / ON a ON
Rx. NOTE MESSAGE OFF / ON 0 ON
Rx. RPK OFF/ ON a On
Rx, NRPH OFF / ON OO{01*) OFF{ON")
eteived, Rx. NRPH will be set OFF. When “GS Reset” is received, it wil be sel ON.
Rx. MODULATION OFF / ON a ON
Rx, VOLUME OFF / ON 0 On
Rx. PANPOT OFF / ON 61 Ou
Rx. EXPRESSION OFF / ON 0 ON
Rx. HOLDI OFF / ON a ON
Rx. PORTAMENTO OFF / ON 0 ON
Rx. SOSTERUTO OFF / ON 0 On
Rx. SOFT OFF / ON ol ON
MONO/POLY MODE Hono / Poly o Poly
{=CG# 126 OF / CC 127 00}
ASSIGH MODE 0 = SINGLE MAPI
IMITED-MULTE a LAMETED-MULT!
MAP?
GO otx=G = SINGLE (Drum Port)
OF otx=/0 — LIMITED-MULTI {Normal Port)
ie porameset that determines how voice assignment will be hondied when sounds overlap on identical note numbers in the some channel {ie., tepeotedly struck notes). This is initialized to 9 made suitoble fo: each Part, s
OFF {Normal Par)
MAPT (Drum Port}