EasyManuals Logo

Roland STUDIO M User Manual

Roland STUDIO M
44 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #10 background imageLoading...
Page #10 background image
S.Gopying
the
System
Disk
&e&
Et
Disks
can be
damaged
or will
eventually
just
wear
out after
extended
use and
may
eventually
become
unreadable
Since
the System Disk
is crucial
to the
operation
of
the MV-30,
make
a backup
copy
or two.
Use a
copy
for
everyday
use, and
keep the original
System Disk in
a
safe
place.
*
Please
use
a
2-DD
type
floppy
disk
(3.5
inch
dual
side
doubte
density double track microtype
diskf such
as a Roland
MF2-DD.
Be awave
that all data that
was
previously
stored
on this
copy
disk
will be erased.
*
You can
use this same
copy
procedure
to
duplicate
other MV-SO
disks
x
lf
you
wish
to copy a
dlsk after
you
have
created
a song r€fitGrt-
ber that
the Gopy operation
will
erase
all this data
from internat
memory.
*
Do
not remove
the Disk
from
the disk
drive until
the
display
reads'tlnsert
Destination
Disk/lnsert
Destination
Disk,,.
o
@
E
t-il]
O
lnsert the
System Disk with the
protect
tab set
to
PROTECT
position
(source
disk) into
the disk drive and
press
the forsx I
key.
€)
Press
the [F5--](Page) key.
The
menu will change.
G)
Press
the [F+l(DskCopy)
key.
The
Disk
Copy and warning
display
will appear.
:
r{
l'll]Rt'l
I t'.lri l
:
J f'
--r,:'Lr
E:{EtrLt+_.g
'
[li
=.k
t]E,p,J'
HErLlr I
l 1rli.E
.=I
l t,rlr-r'-I
d.=L.=.
I ns.ert-.
E;,=r_rr.re
tli
s.k
TilEEilIIH
@
Press
the [fl](Execute)
key.
The
MV-30 will begin reading
data from
the
disk.
O
When
the display reads
"lnsert
Destination
Disk", remove
the System
Disk,
insert
the copy
destination
disk with
the
protect
tab
set to WRITE
position,
and
press
ffil(Execute)
key.
After
the disk has been
formatted
for
the MV-30,
the
System
Program
will be written
onto
it.
@
wnen
the
display reads
"lnsert
source
Disk",
remove
the
disk, and
insert
the
copy
source
(System)
disk.
O
Repeat
steps 4,
5 and 6
(disk
swapping)
until the
display
reads
"Complete",
indicating
that
the disk copy operation
has
been
completed.
Note
that
this
entire
process
may
take several
minutes.
@
Press
tFtAY-l
to
return
to the opening
display.
1l
...

Other manuals for Roland STUDIO M

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Roland STUDIO M and is the answer not in the manual?

Roland STUDIO M Specifications

General IconGeneral
BrandRoland
ModelSTUDIO M
CategoryMusic Equipment
LanguageEnglish

Related product manuals